动力和非动力轴的弯度和调整压力，以及连同滚筒盘中的轴的偏差在设计中都得到体现。
Power and non power shaft bend and adjust the pressure, and together with the roller disk axis deviation have been reflected in the design.
结合其开放式构架和标准原料产品，这样就帮助提供改善了的可用性而且支持传统的动力轴驱动控制。
This, combined with its open architecture and standard off-the-shelf products, helps provide improved usability and support over traditional line shaft drive control.
每一组收缩都会对环绕在传动轴上的项圈产生压力，于是，这些搏动的肌肉会一齐连续地挤压传动轴，形成转动力，从而产生旋转。
As they do so, each pair applies pressure to a soft ring around the driveshaft. The pulsating muscles collectively and continuously pinch the shaft and apply a rotational force, causing it to turn.
这款9.3英寸长的空气动力学传家宝式玩具拥有玛瑙心车轮、严丝合缝的轴承和不锈钢轴，可由这一代传给爱车的下一代。
The 9.3-inch-long aerodynamic heirloom toy, with its carnelian-core wheels, precision bearings, and stainless steel axles, is built to be passed down from generation to car-loving generation.
在阶跃轴压载荷情况下，动力载荷可能激发比静力载荷更高阶的屈曲模态。
Under the axial step load case, dynamic load tends to inspire a higher order buckling mode .
为了测量拖拉机动力输出轴的输出功率，设计了一套计算机辅助测试系统。
We design a set of computer aided test system for measuring the output power of the tractor motive power shaft.
动力传到螺杆轴上，由螺杆带动星轮旋转。
Power reached the screw axis, Driven by the star wheel rotating screw.
为验证模型有效性，将其应用于某三轴稳定对地定向卫星姿态动力学仿真中，得到了相应的太阳光压干扰力矩曲线。
As illustration, these models are applied to an attitude control dynamics simulation of a three-axis stability satellite and the corresponding toques were plotted in curves.
一般而言，空心轴式的体积较小，而所需磁化力(磁动力)亦比伸出轴式为小。
Generally speaking, hollow shaft type of small volume, but the amount of magnetic force (magnetic power) also stretch out shaft type than for small.
最后本文提出了一种采伐机具新的设计思路，即以小四轮拖拉机动力输出轴为动力源的设计方法，并最终初步设计了一种柠条灌木林的采伐机具。
A new design thought was proposed: the design technique which use the power output axis of tractor as the origin of power, furthermore, a Caragana cutting machine was primary designed.
对播种机构进行了改进，设计了动力驱动粉碎刀轴与圆盘开沟器组合的防堵机构。
A new anti-blockage mechanism, which combines the powered chopping and disc opener, was designed and tested.
目的：探讨高度近视眼后巩膜形态改变与眼轴长度、近视程度及血流动力学变化之间的关系。
Objective: To explore the morphological changes of rear sclera in myopia and the relation among the length of eye axis and the degree of myopia and hemodynamic changes.
该多周期扰动力矩与转台三轴转速有关，影响转台的定位精度、位置精度和速率精度。
The multi-period disturbance torque is related to three-axis rotate speed of turntable and influences localization precision, position precision and speed precision of turntable.
本文将简化传递矩阵法扩展用于计算有分义或内、外套轴的各种复杂转子的动力特性。
In this paper the simplified transfer matrix method is extended and used for the dynamic analysis of complex composite rotor systems.
在任何操纵面上的空气动力均产生围绕其铰链轴的力矩。
The aerodynamic forces on any control surface produce a moment about the hinge.
在这些装置中，典型的情况是，一根轴由发动机或皮带轮传动，另一根轴将动力传递给其他部件。
In these devices, one of the shafts is typically driven by a motor or pulley, and the other shaft is driving another device.
最后通过动力三轴试验仪研究冲击荷载作用下红粘土的力学和变形特性。
Finally use the dynamic three axle shear test to research impulsive load function under red clay mechanics and distortion characteristic.
梁非线性动力分析中剪切力和轴力的相互影响。
Interaction of Sheering and Axial Forces in Nonlinear Dynamic Anaysis of Beam.
介绍了2e轴中交叉支撑低动力作用货车转向架的主要技术参数、设计思想、设计结构及试验等情况。
The main technical parameters, design thought, design structure and testing of the higher cross braced low power freight car bogies with 2e axles are described.
在通往内地的管道中，设三叶以上的叶轮水流轴传动用作发电或取动力。
Pipeline leading to the Mainland, located above the impeller flow trefoil drive shaft for power generation or to take power .
从齿轮传动的基本原理出发，系统地分析了多轴齿轮传动系统的动力学模型原理，提出了基于齿轮副接触算法的动力学仿真模型。
The gear transmission system dynamics model was analyzed according to the gear transmission principles and a dynamics method based on gear contact calculation was given.
首先，本人设计的零件为轴，它的作用是起到传动作用，传动力的方向和轴力。
First, I designed components for the shaft, and its role is to drive, Chuan dynamic direction and axial force.
动力启动方轴传动装置。销法兰。无油密封垫圈。
Power take - off, squared shaft drive. two stud flange without oil seal gasket.
首先，本人设计的零件为输出轴，它的作用是传动作用，传动力的方向和轴力。
First, I designed components for the output shaft, and its role is to drive, Chuan dynamic direction and axial force.
齿轮段也有输入轴和输出轴，它必须吧动力传递给驱动轮。
The gear section also has the input shaft and the output shaft needed to transmit power to the drive wheels.
齿轮用于两个不同传递的轴之间的动力传递。
Gears are used to transmit power between shafts rotating usually at different speeds.
齿轮用于两个不同传递的轴之间的动力传递。
Gears are used to transmit power between shafts rotating usually at different speeds.
应用推荐