作废支票是否按规定销毁？或者剪角保留供以后检查？
Are voided checks properly deface or mutilated and held available for subsequent inspection?
试验表明，压实度、压实含水量及土体饱和状态对粘聚力和内摩擦角有影响，从而使抗剪强度也受到三因素的影响。
Results show that degree of compaction, compaction water content and saturation state of compacted soil have influence on cohesion and Angle of friction of clay, thereby on the shear strength of clay.
在管道跨越工程中，常用三角形截面组合管拱，由三角形截面桁梁的受力分析图，分析推导出其抗剪刚度。
The pipeline bridge is built up with triangle sections, its shear stiffness can be derived from the stress diagram for the truss with triangle section.
取放射线分区剪三角堆积层次。
土壤抗剪黏聚力和内摩擦角，是评价土壤抗剪性能的两项指标。
Soil resistance and pastes cohesion and internal friction Angle, is the two indicators which evaluate the performance of soil shear.
取水平分区剪三角堆积层次并与第一分区不连接。
Take horizontal section cut a triangular graduation which disconnected with first section.
取斜线分区剪三角堆积层次。
结果显示，当上覆压力较小时，剪胀角对抗拔应力的影响较小。
Parametric analysis is carried out to investigate the effects of soil dilation and overburden pressure on the soil nail pullout resistance.
主裂缝的总体传播方向与断层平面的夹角约等于土体在土层平均围压下的剪胀角。
The propagation angle of the principal fault rupture through soil equals the dilation angle of the soil under the mean confining pressure.
取斜向前偏垂直的分区剪三角反曲线层次。
分析了入射角改变对焊接件外观形貌、焊缝截面、焊缝板间连接宽度以及所承受的拉剪载荷的影响。
The transverse weld topography, the connect width between plates and tension and shear load were analyzed when the incident angle changed.
大六角头高强度螺栓连接副扭矩系数的检测，扭剪型高强度螺栓连接副坚固预拉力的检测，高强度螺栓连接磨擦面抗滑移系数的检测，是钢结构材料验收中的重要测量。
To determine the anti-slip coefficient of the high-strength bolt which connects components of friction surface, it is screwed and determined by torsion and tensile testing machines respectively.
给出了塑性区中平均体积应变及弹、塑性变形体积的计算公式和剪胀角的测试方法。
The expressions of elastic deforming volume and plastic deforming volume in the plastic zone were presented together with the average plastic volumetric strain.
钢结构系列：钢结构用高强度大六角头螺栓，扭剪型螺栓连接副，钢网架球节点用高强度螺栓，焊钉，钻尾丝等。
Steel Series: steel with high strength large hexagon head bolts, torsion shear bolt connections made, the steel truss joints of high strength bolts, studs, drill the end of wire.
对不同厚度及缺角的速生材试样，进行了顺纹抗剪强度的测定。
The objective was to examine the effect of sample thickness and cutting angle on the shear stre…
对不同厚度及缺角的速生材试样，进行了顺纹抗剪强度的测定。
The objective was to examine the effect of sample thickness and cutting angle on the shear stre…
应用推荐