• 通过对飞剪剪切长度,精度,剪刃间隙和压板机构等参数的优化,来提高钢板的剪切质量。

    Optimizing the parameters of shearing lengths, shearing accuracy, blade clearance and pressure plate mechanism, so as to improve the shearing quality of steel plates.

    youdao

  • 在仔细研究了引进设备剪切长度模型的基础上,本文提出了一种按照轻型材和重型材的不同分段特点分别建立数学模型的新办法。

    In this paper, a novel method, which is to establish the mathematical model according to the different specialities of the light and the heavy shape steel, is presented.

    youdao

  • 随着腔内平板长度的增加,剪切层振荡的程度有所减小。

    The oscillation of the shear layer decreases with the increase of the plate length.

    youdao

  • 虽然偏离值可能不大,但利用对数剖面去计算河底粗糙长度和剪切应力时会引起较大的误差。

    The amount of the departure may not necessarily be large, but it results in the larger errors when the profiles are used to calculate the bed roughness length and shear stress.

    youdao

  • 斯罗曼飞剪机是实现带钢定尺剪切的重要设备,其运行速度与带钢的长度和厚度有关。

    SILMEN full-speed shearer is an important device for fixed-scale steel tape shearing. Its running speed is highly related to the length and thickness of the steel tape.

    youdao

  • 得出了在不同拉伸速度和边框长度条件下装置处于准静态时的临界剪切角,并且分析了织物试样尺寸大小对准静态范围的影响。

    The critical shear Angle of quasi-static state was given under different loading speeds and frame lengths condition, and the influence of specimen size on this shear Angle range is also discussed.

    youdao

  • 研究结果表明: 防热涂料的剪切强度分散性较大,这主要是由于溢胶现象使得搭接长度的准确测量比较困难,同时造成了试件的对中性较差。

    The results show that the data of shear strength are discrete. The main factor is the overflow dope that causes the lap length to be measured difficultly and the centerline disagree.

    youdao

  • 适当增加流道的长度,可以减小胶料出口处的速度场、剪切速率场的集中程度并使之趋于均匀,能够有效降低挤出胀大和模外熔体偏转流动现象。

    The velocity field and shear rate distribution are reduced and uniform along with the proper increase of slip length. The die swell and the interface deflexion phenomenon will be reduced effectively.

    youdao

  • 随剪切速率的增加,压力振荡的振幅减小,而滑移速率、临界外推滑移长度及振荡频率均有提高。

    As the shear rate rises, the amplitude of pressure oscillation reduces, whereas the slide velocity, critical slide length and the frequency increase.

    youdao

  • 从流体力学的角度来看,这个无剪切界面对应着流体中的滑移边界条件,而与此相关的概念是有效滑移长度。

    From the view of fluid mechanics, the shear-free air water interface corresponds to a slip boundary condition in fluid and relatives to the concept of effective slip length.

    youdao

  • 方法测试和比较含氟牙釉质粘接剂及不含氟牙釉质粘接剂的剪切强度以及扫描电镜下粘接剂渗入酸蚀后牙釉质表面形成的树脂钉突长度。

    Methods To test and compare the shear bond strength and the penetration depth of resin tags of fluoride-releasing orthodontic adhesives with those of the traditional orthodontic adhesive.

    youdao

  • 该电热带在现场能按实际需要长度任意剪切,并具有柔软性,可以紧贴管道表面敷设。

    The electric heating belt can be cut flexibly according to the actual needs. And it is flexible and can be installed closely on the pipe surface.

    youdao

  • 非贯通节理岩体多层结构模型假定岩桥为共面剪切破坏,模型适用于岩体节理共面并且岩桥长度远小于节理长度的情形。

    This model assumes the coplanar shear failure mechanism of the rock bridge, so it can be used under the circumstance that the length of rock bridges is far less than of the length of the joint.

    youdao

  • 该系统能够逻辑控制剪刃的运行规律,保证剪刃线速度与轧件线速度同步,保证剪切产品长度的定尺精度。

    The system keeps the linear velocity of the shear blade in pace with that of the rolled piece and warrants the accuracy of the specified cut length.

    youdao

  • 该系列生产线用于不同规格的卷料,经过开卷、矫平、剪切成为所需长度和宽度的平整板材。

    This production line is used for coil with different specifications, through uncoiling, leveling and cutting to length to flattened plate as needed length and width.

    youdao

  • 研究发现初始滑移长度对低剪切率下的滑移行为起主要作用,而临界剪切率决定了高剪切率下的边界滑移程度。

    It is found that the initial slip length controls the slip behavior at small shear rate, but the critical shear rate controls the boundary slip at high shear rate.

    youdao

  • 研究发现初始滑移长度对低剪切率下的滑移行为起主要作用,而临界剪切率决定了高剪切率下的边界滑移程度。

    It is found that the initial slip length controls the slip behavior at small shear rate, but the critical shear rate controls the boundary slip at high shear rate.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定