本文研究设计了电子剥离试验机,并对其可靠性进行了分析。
In this paper, we present the research and design of the Electronic stripping tester and analysis the reliability of the tester.
并根据4种玻璃钢骨架的剥离试验数据,计算出玻璃钢渔船舭龙骨的连接强度。
And the connection strength of the bilge keel of FRP fishing boat was obtained based on the ripping tests of 4 FRP frames.
复合钢板经焊接工艺评定和抗氢剥离试验证明,该产品具有优良可靠的制造和使用性能。
Evaluation of welding process and hydrogen -resistant peeling test of the clad plate shows that this product possesses excellent, reliable manufacturing and operation properties.
研究工作从两方面入手:一是在车辆制动系统方面开展了试验研究,二是采用合金化的车轮提高抵抗剥离的能力。
The research begins from two aspects:one is that test and research are done in the car braking system, the other is that the alloyed wheels are applied to improve the ability of spalling resistance.
声发射划痕试验表明,在最大载荷100n的作用下,熔覆层与基体结合良好,没有剥离和崩落现象。
Launch scratch test indicate under most big load function of 100n, cladding layer combine substrate well, there are no stripping and avalanche phenomenon.
通过硅橡胶力学性能试验,得出用硅橡胶的拉伸、撕裂、剥离强度等性能指标,可以满足气囊模具的要求。
Tested the mechanical properties of silicon rubber, tensile, tearing and peeing strength can are meet the demand of inflatable bag.
通过对过热器结垢状况、机理分析及清洗试验研究,研制出过热器专用清洗介质体系,具有除垢速度快、溶垢性强、防剥离性好、无毒等优点。
Through analyzing the scale situation and mechanism, and carrying out the cleaning test and study of once- through boilers superheater, the special cleaning medium system of superheater was developed.
试验结果表明:降低应力集中及剥离应力小的接头形式可有效地提高胶接强度。
The results show that the joint forms which have less stress, concentration and less peel stress can raise bonding strength greatly.
涂覆应用试验表明,该涂覆专用料产品质量稳定,成膜均匀,剥离强度高,且降低了加工温度。
The test of coat application shows that the film has stable quality, uniform film formation and high peeling strength, as well as lower processing temperature.
介绍了高龙公司利用露采剥离贫矿进行大粒度、大堆高的堆浸提金试验。
This paper introduced the experiments on the large grain size and high heap gold leaching of stripped lean ore from open pit mining of gaolong co.
通过室内模拟试验来研究水位对沥青混合料水稳定性的影响,同时对掺加熟石灰抗剥离剂的改善效果加以评价。
The effect of water on moisture stability of asphalt mixture was studied by simulated test in the laboratory, and the performance of asphalt mixture with hydrated lime additive was analyzed.
综合介绍了各种碎解条件对废纸碎化、油墨剥离和浮选脱墨的试验结果。
The test results of repulping parameters on deflaking, ink detachment and flotation deinking were introduced in this paper.
介绍粘泥剥离剂的评价方法以及高效粘泥剥离剂Q S-17在中试装置试验的情况和结果。
Presents the appraisal method of the sludge strippers, as well as the testing and result of high efficiency sludge stripper QS-17.
对钢丝缠绕增强塑料复合管应变、剥离强度、临界失稳压力、不同温度下的失效形式等进行了试验研究。
Strain, peel strength, critical buckling pressure and failure mode under various temperatures of PSP were investigated using experiments.
经环境试验证实能够达到防霉防盐雾的效果,进一步证明了该可剥离防护膜具有良好的性能。
The environmental test results for antimildew and antifogging were very satisfactory, which proved the good performance of the protection film.
介绍了用堆浸法从剥离贫矿石中回收黄金的工业试验条件及结果。
The conditions and result of a commercial scale trial of gold extraction from stripped barren ore by heap leaching process are reported.
研究工作从两方面入手:一是在车辆制动系统方面开展了试验研究,二是采用合金化的车轮提高抵抗剥离的能力。
The research begins from two aspects:one is that test and research are done in the car braking system, the other is that the alloyed wheels are applied to improve the ability of spalling resist…
通过一系列电解充氢试验比较了不同焊后热处理条件对不锈钢堆焊层氢致剥离的影响。
The influence of PWHT conditions on hydrogen-induced disbonding were studied through a series of electrolytic hydrogen charging tests.
试验结果显示:铁、镍、钼元素分布变化不大。熔合线堆焊层侧增碳层宽度增加,氢致剥离的倾向也增大。
The results show that there are little changes in the distribution of Fe, Ni and mo, the increase of the width of carburized zone will promote the tendency of hydrogen-induced disbonding.
测量界面强度的主要困难在于寻求一种便于试验的试件形状和加载方式,使得界面上能够产生不同的应力状态,即在不同的剥离应力和剪应力比的状态下发生破坏。
The main difficulty is to find a test method with simple specimen shape and loading style to cause different interface stress modes, that is, normal stress and shear stress dominated modes.
分析结果表明,本文提出的计算模型与试验结果吻合良好,可以真实模拟受弯剥离破坏过程。
Through comparisons with the test results of 45 beams, this method is shown to provide accurate predictions of IC debonding failures.
分析结果表明,本文提出的计算模型与试验结果吻合良好,可以真实模拟受弯剥离破坏过程。
Through comparisons with the test results of 45 beams, this method is shown to provide accurate predictions of IC debonding failures.
应用推荐