困难的部分是有地方前轴承会。
The difficult part is there where the front bearing will be.
如需要，安装小齿轮前轴承。
前轴现在配备的普遍摆动轴。
松开前轴横梁上的拖臂并从支座中拔出。
Loosen trailing arm on front-axle cross member and pull out of the mount.
它将无论是工作后或前轴。
添加前轴与车轮和间隔，所显示的说明。
Add the front axle with its wheels and spacers, as shown in the illustration.
阐述了某汽车前轴的垂直弯曲疲劳试验。
A vertical bending fatigue experiment for a certain model of automotive front axle is reported in this paper.
应检查车架或前轴的技术状况及转向机构情况。
Frame or the front axle should check the technical condition and the situation of steering.
前轴延伸，以确保佩戴舒适和密封冷空气出来。
Front shaft stretches to ensure a comfortable fit and seals cold air out.
介绍了重卡前轴预成形辊锻工艺试验与结果分析。
The process experiment and result analysis of preceding roll forging for heavy truck front axle introduced in this paper.
讨论了随机参数服从非正态分布前轴的可靠性优化设计问题。
This paper examines the reliability optimization design for front-axle with non-normal distribution parameters.
新a5和奥迪的其它系列的主要差别是其发动机将被置于前轴后端。
The key difference between the new A5 and the rest of Audi's lineup is that the engine will now be placed behind the front axle.
在向前轴距设计-与前部和定位在哪里你通常会发现他们前进后轮。
Forwardly designed wheelbase - with both front and rear wheels positioned forward of where you normally find them.
在调整前轴和后轴的车轮定位值之前，建议检查空重下的车辆高度。
Before wheel alignment values are adjusted at the front and rear axles it is recommended that the vehicle height be checked at the empty weight.
新A5和奥迪的其它系列的主要差别是其发动机将被置于前轴后端。
The key difference between the new A5 and the rest of Audi's lineup is that the engine will now be placed behind the front axle .
碟刹成为各地标准和贝尔住房的前轴改变，以适应更大的还原齿轮。
Disc brakes all around became standard and the bell-housing of the front axle was changed to accommodate larger reduction-gears.
通过万向节轴将齿轮传递的力矩分配给前轴主减速器或后轴差速器。
Distributes the moment released by the gear via the cardan shafts to the frontaxle final drive or rear axle differential.
论述了中吨位汽车前轴辊锻成形工艺参数的确定方法和模具设计要点。
The selection method of roll forging process parameters of middle tonnage automobile front axle and die design outline were stressed.
试验完成取下试件检查前轴与前叉之间是否有相对位移，判断是否合格。
Taking off the test items to check have relative shift between front axle and front fork to judge if eligible.
使用带有经过优化的减震器的衬块更换前轴制动片，拆卸和安装前制动片。
Replace the front brake pads with pads that have an optimised vibration damper removing and installing front brake pads.
目前轴承行业中，轴承清洗的方式主要是以汽油或煤油作清洗介质的喷淋清洗。
In the bearing trade at present, the way in which the bearing cleaning is mainly spout with the petrol or the kerosene.
将新式主动横向稳定器安装在中型货车的前轴和后轴，通过液压缸与车架连接。
In this paper, the new type of active roll stabilizers are mounted on the front and rear axle of an experimental medium-duty truck, which are connected to the frame through their hydraulic actuators.
与传统方法相比，该方法更能迅速准确地得到车辆前轴的可靠性稳健优化设计信息。
Comparing with traditional methods, the reliability robust optimization design information of automobile front-axle can be obtained accurately and quickly by the proposed method.
用户可以通过前轴设计模板和使用前轴专用菜单命令快速完成前轴总成的设计过程。
Users can realize the rapid designing on the basis of the design template of the front axle and the command of the special menu system.
无论是前轴心时代、轴心时代、轴心时代以后，乃至今天，神话的魅力仍未见消退。
The charm of myth has still not seen the retrogression from pre-axis age, axis age, post-axis age till today.
前轴精密辊锻工艺难度大，模具设计主要是靠查手册，用经验公式来确定的模具参数。
Furthermore, the design parameter of rolling forging die is acquired from mechanical design handbooks and experiential formula.
外壳通过位于前端支架和前轴承座之间的特殊滑动部件向前滑动，从而避免了热膨胀的影响。
The casing is thus free to yield to thermal expansion by moving forward on special slide elements between the front-end brackets and the front bearing pedetal.
最后，对前、后轴两种驱动方式进行了比较，工业锅炉链条炉排采用前轴驱动方式更为合理。
A comparison of the two drive modes, namely, the front and rear shaft drives, has led to the conclusion that a front shaft drive is more rational for use on industrial boiler chain grates.
本文主要介绍了空冷贝氏体钢在重型汽车前轴上的应用研究，探讨了影响强度与韧度的一些因素。
The article mainly introduces the application of air - cooling bainite steel at heavy truck front axes and discusses some factors affecting strength and toughness.
在整个结构设计中，捡石机的前轴没有相应的结构设计标准，而且该轴的受力复杂，对强度要求较高。
In the entire structural design, the front axle of rock picker can not be designed standard, moreover this axis stress complex, is high to the intensity request.
应用推荐