最后，提出了螺旋切槽松动爆破的方法及优点。
他们也可以用于钻、钻孔、切槽的齿轮，和生产。
They can also be used to drill, bore, cut gears, and produce slots.
为此，往往在动盘本体园周部门，沿径向和周向切槽。
Therefore, often in dynamic disk ontology garden weeks department, radial and circumferential cutting.
提出用边切槽圆盘试样测量岩石动态断裂韧度的实验方法。
An experiment on dynamic rock fracture toughness test using edge-notched disc specimen is presented.
如果过渡段被电镀(倒角和内切槽)将会产生应力集中，造成裂纹。
Plating into a transition (radius transition or undercut) will create a stress concentration that can cause crack initiation.
其特点是将国棒料固定，切槽刀随主轴刀盘回转的同时作径向切削运动。
The round bar to be cutis fixed and the grooving tool is rotating with spindle, in the meantime, the tool is fed in radially.
因此研究切槽定向断裂控制爆破的爆破机理及相关参数，具有十分重要的意义。
Therefore, it is very important to study the mechanism and the related parameters of notched directional splitting controlled blasting.
在公路路堑切槽开挖硐室控制大爆破中，采用较大不耦合比较进行松动控制爆破。
Bigger uncoupling is adopted to realize loose controlled blasting in the excavation of chasm notch blasting.
只要能满足断屑条件，无论是车外园、搪孔、切槽、切断均能达到自动断屑的目的。
It can be applied to turning, boring, grooving, and cutting-off, realizing automatic breaking of chips once the conditions for chip breaking is satisfied.
本系列是万能型立式车床，可用于内外圆柱面、圆锥面、端面、切槽等粗、精加工。
This series are universal type VTL, and we can use for inside and outside cylindrical, conical, end and notch of roughing and fine machining.
通过三维边界元计算分析表明，切槽宽度越大，无量纲应力强度因子的标定值就越大；
Our 3D BEM(Boundary Element Method) calculation shows that the larger the notch width is, the bigger the error makes for the dimensionless stress intensity factor.
软土中的机械预切槽法是超前支护的一种，在预筑拱的保护下可以安全高效地开挖隧道。
The Mechanical pre-cutting method used in soft ground is a kind of preparative support, it allows tunnel excavation work to be conducted efficiently under the safe pre-lining.
本文针对硬质合金刀具切削中硅铝合金活塞槽存在的问题，研制出一种新型人造金刚石切槽刀。
For the problems that exist in cutting medium silicon aluminium alloy piston grooves with carbide tools, this paper presents a new kind of artificial diamond grooving tool.
发热部是双螺旋切槽，在电流通过时可以减少其横截面积，因而发热部的阻值比冷端部的阻值大。
The hot zone is formed by cutting a double spiral slot which reduces the cross sectional area through which current flows, resulting in higher resistance than the cold end.
详细讨论了“V”型切槽在冲击波的动态压力和爆轰气体的准静态压力作用下所产生的力学效应。
The mechanical effects produced by the V-shape notch, which is under both the dynamical pressure of explosive shock wave and the quasi-static pressure of explosive sas, are discussed in detail.
路面切槽机通过四连杆机构可以调整切割深度，采用切割卡轮，保证锯片不跑偏，保证切割准确。
Road cutting through the slot machines four linkage cutting depth can be adjusted by cutting card round, saw no guarantee that deviation, and ensure accurate cutting.
两滚筒旋转，将调配好的试料沿两滚筒上方之切槽倒入，两边的挡料板亦也可根据需要略作调整。
Two drum rotation, a good specimen will deploy along the top of the two rollers into the notch on both sides of the retaining plate also can be slightly adjusted as needed.
YAG固体激光切槽是当前最先进的连杆裂解槽加工工艺，但其激光加工参数的选择主要依靠经验。
YAG solid laser notching is an technology, but the choice of laser processing parameter depends on experience mainly.
处理方案主要包括骑缝切槽、水下灌浆、骑缝切V形槽、嵌压SR止水材料、粘贴SR防渗盖片等。
The treating schemes were included the followings: slotting across cracks, grouting under water, V-shaped slotting across cracks, caulking SR materials, pasting impervious SR cover sheet.
融合不当可能会改变要求的喷丸层或在镀层边沿产生内切槽或凹槽，可能会造成使用过程中产生裂纹。
Improper blending can remove the required shot-peened layer or create undercuts or grooves at the edge of the plating that can cause cracking in service.
利用断裂力学原理阐明了切槽爆破机理，提出了切槽预裂爆破的刀具参数，依据现场初步试验成果指出了下一步应改进的切槽刀具参数。
The notch blasting mechanism is expounded by the fracture mechanics principle, the cutting tool parameters for notch presplitting blasting is put forward.
螺旋槽成形铣削时普遍存在根切现象，在很大程度上影响到加工精度和几何形状。
Usually, there exist undercutting phenomena in helical groove milling process, which affect the accuracy and geometrical shape greatly.
方法三棱滑切固定矫治器的结构，以三棱形弓丝和具有三角槽沟的托槽为主体，由它控制矫治牙在各个方向的移动而发挥矫治作用。
Methods the structure of deltoid arch wire fixed appliance is consist of deltoid arch wire and bracket with deltoid colpus. It is used to control the tooth's moving.
根据零件的孔、槽等剖切特征，提出基于优先度和基于图遍历的两种自动搜索关键特征产生剖切线的算法，并分别结合实例进行了比较。
This paper proposes two algorithms based on priority analysis and graph traversal respectively to automatically choose the section cut of key features such as holes and slots.
根据零件的孔、槽等剖切特征，提出基于优先度和基于图遍历的两种自动搜索关键特征产生剖切线的算法，并分别结合实例进行了比较。
This paper proposes two algorithms based on priority analysis and graph traversal respectively to automatically choose the section cut of key features such as holes and slots.
应用推荐