高阻电路的切换应用包括小电流、高电阻和高阻抗电压应用。
Switching applications of high impedance circuits include low current, high resistance, and high impedance voltage applications.
在有些应用中，例如测试电缆和印制板的绝缘电阻及耐压测试，可能需要切换高压信号。
Some applications, such as testing insulation resistance of cables and printed circuit boards and high-pot testing, may require switching high voltages.
当切换低压信号并进行低电阻测量时，可通过偏移补偿的方法消除热电效应偏移电压。
When switching low voltages while making low resistance measurements, the thermoelectric offset voltages may be canceled by using offset compensation.
在有些应用中，例如监测电化电池和测量半导体的电阻系数，则可能必须进行高阻抗电压切换。
High impedance voltage switching may be necessary in applications such as monitoring electrochemical cells and measuring semiconductor resistivity.
如果被切换电流足够高，通道电阻会引起明显的电压降。
The channel resistance may cause a significant voltage drop if the current being switched is high enough.
在将一个电压源切换至多个装置时，则可能必须补偿由于开关电阻引起的压降。
When switching a voltage source to multiple devices, it may become necessary to compensate for voltage drops due to switch resistance.
为了增加更多的死区时间，补偿功率管的切换瞬间短暂延时，增加了一个肖特基二极管，与栅极电阻。
The schottky diode bypasses the gate resistor in the gate discharge path, so that there is no falling edge delay. The delay at the rising edge adds dead time.
电容器漏泄测量和多芯电缆绝缘电阻测量是切换容性负载容易发生问题的两类应用。
Capacitor leakage measurements and insulation resistance measurements of multi-conductor cables are two applications where switching capacitive loads may be a particular problem.
切换采样转子一点接地保护，通过两个静态开关一开一合建立两组方程来求解接地电阻与位置。
Commonly, by opening one switch and closing the other, two group equations are set up to measure rotor earth-fault resistance in the rotor earth-fault protection with switch sampling principle.
为使通道电阻引起的测量误差最小化，则采用4线切换电路。
To minimize measurement error due to channel resistance, use a four-wire switching circuit.
在多点温度巡回检测系统中，多路切换部件干簧继电器接触电阻的变化是影响系统精度的主要因素。
In multiple-channel scanning thermometrical system, the change of connecting resistance of tongue relay is the main factor which influences the system precision.
在商用的切换硬件中，RCH和CCH被作为通道隔离(以电阻和电容给出)或“通道-通道”串扰(以抑制dB给出)。
In commercially available switching hardware, RCH and CCH are referred to as channel isolation (given in resistance and capacitance) or as channel-to-channel crosstalk (given in dB rejection).
前置放大电路设计了量程自动切换的电阻反馈式两级放大。
A range automatic transfer is designed for the preamplification system with resistance feedback.
本发明提供一种可达到至少两个稳定的电阻率状态的电阻率切换金属氧化物或氮化物层。
The invention provides a resistivity switching metal oxide or nitride layer capable of reaching at least two stable resistivity states.
零电压切换开关的可能性电阻器或电机。
Possibility of zero voltage switching to switch resistors or motors.
对于稳定低接触电阻、低电容、高绝缘电阻、长寿命和小组装尺寸的切换应用而言，干簧继电器为最理想的选择。
Reed relays are ideal for applications requiring low and stable contact resistance, low capacitance, high insulation resistance, long life and small package size.
利用该统一模型，分析了外加直流电压法、外加交流电压法、乒乓切换法中电刷接触电阻对励磁绕组接地电阻测量值的影响和危害。
By using power of DC superimposed AC, oxidation rate rose with increase of voltage but had nothing to do with frequencies in this experiment.
利用该统一模型，分析了外加直流电压法、外加交流电压法、乒乓切换法中电刷接触电阻对励磁绕组接地电阻测量值的影响和危害。
By using power of DC superimposed AC, oxidation rate rose with increase of voltage but had nothing to do with frequencies in this experiment.
应用推荐