不同磨粒的法向力与切向力有着良好的线性关系。
With the same cutting velocity, the grinding forces have good linear relationship with plowed surface area.
改变坐角显著影响脚蹬切向力、有效力及作用效率的大小。
The change of the seat Angle affects significantly the tangential force, the efficiency of the force, and action efficiency.
用向心力和切向力或离心力和切向力进行胁变分析是可行的。
Centripetal force and tangential force or centrifugal force and tangential force could be used as a strain analysis method.
用解析的方法，给出了径向力和切向力随时间变化的具体表达式。
Expressions of radial force and torque variance were obtained by analytical method.
假设当两个接触面处于相对滑动的临界状态时，切向力与垂向力成正比。
Provided two contact bodies are in the critical state of relative sliding, the tangential force is proportional to the vertical force.
那么单摆在振动过程中，切向力、法向力及合力的大小和方向是否在变化?。
Do the tangential force, the mormal force, the resultant force and their directions during oscillation of a simple pendulum change?
在所有附加力中，只有切向力对流体产生影响，离心力和科氏惯性力的影响相互抵消。
Of all the additional forces, only the tangential force effects on the flow. The effect of centrifugal and Coriolis forces on the flow is counteracted.
接触问题是非线性问题，涉及到应力集中、局部边界非线性、切向力的不可逆性等一系列非线性问题。
The contact problems are non-linear problems, which relate to stress concentration, local boundary nonlinear, no-reversibility of shear force, and so on.
得到不完全边界上不同反射波和透射波的振幅比，并导出法向力刚度、切向力刚度和完全粘接时的振幅比。
The amplitude ratios of different reflected and transmitted waves were obtained for an imperfect boundary, and deduced for normal force stiffness, transverse force stiffness and perfect bonding.
通过测量高频感应钎焊金刚石砂轮磨削花岗石过程中的磨削力，对砂轮所受的法向力和切向力进行了研究。
In this paper, grinding forces were measured in the grinding of granite with a high-frequency induction brazed diamond grinding wheel.
计及作用于接触斑点上的切向力，通过比较作用于接触斑点上的法向弹性载荷与法向塑性载荷，确定了区分弹性接触与塑性接触区域的临界接触斑点面积。
Considering the tangential force applied on a contact spot, the critical area demarcating the elastic and plastic regimes is obtained by comparing the normal elastic load with the normal plastic load.
重点研究了加工单晶材料时晶向对临界切深、微切削力和表面粗糙度的影响；
The crystallographic effects on critical depth, micro cutting forces and surface waviness when machining single crystals are emphatically investigated.
通过测量主轴功率获得切向磨削力，讨论了加工参数，如切深、进给率以及砂轮粒度对切向磨削力的影响。
Tangential grinding forces are obtained through monitoring spindle power and the ir variations are studied with process parameters such as depth of cut, feedrate and wheel grit size.
在非稳流下，采用函数拟合法，得出流体切向速度随半径变化的表达式及流体所受切向剪切力和分布曲线。
Secondly, in conditions of non-steady flow, azinuthal velocity and shear stress distribution were deduced according to function approximation method.
切向冻胀力在桩身缺陷处，会产生应力集中，使桩身破坏。
The tangent frost heaving stress will generate stress concentration at the pile defects, thus damaging the pile body.
对于扩颈桩，由于扩颈处桩周侧面积增大而使切向冻胀力增大对桩产生不利影响。
As for the pile with the expanding neck, the tangent stress grows due to the increased area around the pile's side, which is detrimental to the pile body.
从切屑变形力与摩擦力两方面分析了切向磨削力与法向磨削力的比值，大体上应在0.2～0.59范围内。
We have also analysed the ratio between tangential forces and normol forces with respect to both chip formation forces and friction forces. The ratio generally falls within the range of 0.2~0.59.
在有限元模型中，分别计算了轮胎在受径向接触面力、切向接触面力和侧向接触面力时的位移频率响应。
The displacement frequency responses of the tires excited by, respectively, radial contact force, tangential contact force and lateral contact force are calculated using FEM.
渗流对裂隙网络岩体的作用力包括渗透静水压力和渗透动水压力(裂隙壁切向拖曳力)两部分。
Flow through fissures in rock mass applies simultaneously the normal hydrostatic seepage pressure and the tangent hauling force (the dynamic seepage pressure) on fissure walls.
渗流对裂隙网络岩体的作用力包括渗透静水压力和渗透动水压力(裂隙壁切向拖曳力)两部分。
Flow through fissures in rock mass applies simultaneously the normal hydrostatic seepage pressure and the tangent hauling force (the dynamic seepage pressure) on fissure walls.
应用推荐