切割电弧稳定，切割速度快，切口平滑，变形小，挂渣少，节省材料。
Steady arc and fast cutting, even cuts, little deformation and slag, material-saving.
软件采用连续曲线算法，切割速度更快。
The software adopts continuous curve method to get faster cutting speed.
尺寸精准，切割速度高。
刀具直径大，切割速度高，加工质量好。
Large tool diameter, high milling speed and good processing quality.
刀具直径大，切割速度高，加工面质量好。
Large diameter of milling knives, high speed milling, good quality milling profile surface.
粒度对表面光洁度和整体切割速度具有重大影响。
Granularity has great influences on the surface finish and integral cutting speed.
增加切割能力或减缓切割速度即可减少这种滞后误差。
Increase of cutting ability or slowing down of cutting speed can reduce the kind of lag error.
成品悬浮率高，流动性好，切割速度快，切后晶片易清洗。
The oil has high suspending rate, fine fluidity, increasing cutting speed and the crystal slice cut by the oil is easy to clean.
切割速度是与所需切割的材料厚度及材质的硬度相关联的。
Cutting speed is related to the thickness and hardness of materials to be cut.
具有切割速度快、切口窄、变形小、节省材料、成本低等优点。
It features high cutting speed, narrow gap, low distortion, materials saving and low cost.
具有切割速度快、切割断面整齐坡角小、定位长度准确的优点。
The invention has advantages of rapid cutting speed, neat cut section with small slope angle and accurate location length.
切割速度对根茬破坏影响最大，速度越高，根茬严重破损率越低。
When the velocity is higher, the serious damage ratio is lower.
超声切割功率的提高，有利于减小切割压力，拓宽切割速度范围。
With the increase of the cutting power, the cutting pressure demand decreases. And the cutting velocity range is extended broadly.
通过切割参数的适当控制，可以在高的切割速度下得到高质量切割面。
By optimizing cutting parameters, high quality can be obtained at high cutting speed.
陶瓷刀具在前三个特性上符合要求，即使在很高的切割速度也没有问题。
Ceramic tools are suitable with regard to the first three properties even at high cutting speeds.
具有阻抗匹配和振幅检测等多项功能，电声转换效率高，发热少，切割速度快。
Because it has many functions such as Impedance matching and amplitude detecting, the system has high electroacoustic transformation efficiency, low heat and rapid cutting ability.
因此，切割氧的纯度、流量、流速和氧流形状对气割质量和切割速度有重要的影响。
Therefore, cutting the purity of oxygen, volume, velocity, and oxygen flow shape on the gas cutting quality and cutting speed has important implications.
通过该模型对一定加工条件下的切割速度和表面粗糙度进行预测，从中找出加工规律。
By the model forecasting the processing speed and surface roughness under some processing requirement, find out the processing law.
使用基于PLC编程语言进行功能设计，并以切割速度调整为例说明其在应用上的可行性。
The paper processes the function design based on PLC programme, and explains the feasibility in practice application taking cutting speed adjustment for example.
锯条切割速度及进给力图表提供了合适的锯条速度和进给力参数，使锯条能发挥最佳性能。
The blade speed and feed charts provide proper blade speed and feed parameters for optimum performance of the blades.
刀片刃口设计合理，使用寿命长，切割速度快。适用于收割水稻、小麦、大豆等庄稼作物。
The blade cutting edge has the advantages of reasonable design, long service life, high cutting speed, being suitable for harvesting crops, such as rice, wheat, soybean, etc.
理论分析和试验结果表明切割深度随着切割速度的减小而增加，随着激光功率的增加而增大。
Theoretical analysis and experimental results all indicate that cutting depth is increasing with the decreasing of cutting speed and increasing of laser power.
结果表明：缝宽随输出功率、频率、脉宽及辅助氧压的增大而增加，随着切割速度的增加而减小。
The results show that the kerf width increases with the increase of laser power, pulse frequency, pulse width and assist gas pressure, but decreases with the increase of cutting speed.
研究了激光光斑直径及离焦量、切割速度、激光功率等工艺参数对齿轮切缝宽度及加工质量的影响。
The effects on kerf width and quality made by laser facula diameter, focal point position, cutting speed, laser power and other technological parameters were studied.
切割速度较低，切割质量也不是很好，但优点是结构简单，可以做的比较大，适合收获谷物或牧草。
Reciprocator cutter works in lower speed and the quality of cutting is not very good. But it is simple and it can be produced very long and large which is very important to harvest rice or wheat.
结果显示在相同的条件下，切缝宽度随切割速度的增加而有一定的变化，随激光功率的增加而显著增加。
Results showed that the cutting seam width varied with the increase of cutting speed and laser output power.
结果表明：金刚石镀膜不仅能够提高锯片的切割寿命，而且可以在降低金刚石浓度的情况下达到最大切割速度。
It is shown that the diamonds with coatings can enhance the service life of the sawblade and obtain a maximum cutting speed at lower concentration of diamonds.
所以，选用尽量小的喷嘴高度对提高切割速度和切割质量都是有益的，但是，喷嘴高度过低时可能会引起双弧现象。
So, choose as far as possible to improve the nozzle of small high cutting speed and cutting quality is useful, but the nozzle at low altitude may cause double arc phenomenon.
幸好，正确的切割速度可以根据刀具寿命表或者刀具寿命泰勒方程估算出来，并有一定的合理精度，如果在必要的数据都具备的前提下。
Fortunately, the correct cutting speed can be estimated with reasonable accuracy from tool-life graphs or from the Taylor tool life Relationship, provided that necessary data are obtainable.
幸好，正确的切割速度可以根据刀具寿命表或者刀具寿命泰勒方程估算出来，并有一定的合理精度，如果在必要的数据都具备的前提下。
Fortunately, the correct cutting speed can be estimated with reasonable accuracy from tool-life graphs or from the Taylor tool life Relationship, provided that necessary data are obtainable.
应用推荐