实验结果表明，该方法不仅可以在多种切削条件下获得较高的识别率，还可以识别出新的刀具故障。
Experiments indicate that this method has a high ratio of recognition in a range of cutting condition and even can detect novel tool faults.
最适合MSR的推荐切削条件是多少？
两种切削条件下均可获得较理想的表面粗糙度。
Under the two kinds of cutting conditions, better surface roughness can be obtained.
论述了径向负前角硬质合金滚刀的设计及切削条件。
Design and cutting condition of carbide hob with radial negative front Angle were discussed.
归一化处理使报警门限设定不受切削条件变化的影响。
The normalized processing makes the setting of the threshold for alarm independent from variation of cutting conditions.
选用的材料种类和切削条件不同，可生成不同形态的切屑。
Different kinds of material and machining conditions used will produce chips of different shapes.
分析不同切削条件下层片宽度的变化及其与变形系数之间的关系。
The variation of the lamella width in different cutting conditions and the relation between the lamella width and the chip deformation coefficient are also analysed.
发现在相同切削条件下，该复合材料表面质量优于ZA22合金。
The results show that the surface quality of the composites is better than that of ZA22 alloy under the same parameters.
提出可根据数控车床设计时选用的典型切削条件来计算机床总刚度。
This paper proposes that the total rigidity of a machine tool can be calculated in terms of the typical cutting condition at the beginning of design for the CNC lathe.
不同刀具材料与工件材料的匹配在不同切削条件下有不同的临界速度。
There are different critical speeds with different cutting condition and different matching of cutter and work-piece material.
金属的实际分离始于屈服或断裂(视切削条件而定)，从切削刀尖开始。
The actual separation of the metal starts as a yielding or fracture, depending upon the cutting conditions, starting from the cutting tool tip.
探讨晶体材料的切削加工性，重点分析切削条件对实现镜面车削的影响。
The paper presents the machinability of crystal materials, and emphasizes the influence of cutting conditions on the mirror finish.
在不同的切削条件下，疲劳裂纹和热裂是造成刀具材料失效的主要原因。
The formation of the fatigue cracks and the thermally induced cracks are mainly responsible for the failure of the ceramic tool materials un der various cutting conditions.
实验表明，通过切削条件和振动参数的优化组合能够得到满意的纤维尺寸。
It shows that the satisfactory equivalent diameter of fibre can be obtained through the optimization of the above parameters and conditions.
在不同的切削条件下，疲劳裂纹和热裂纹是造成刀具材料失效的主要原因。
The formation of the fatigue cracks and the thermally induced cracks are mainly responsible for the failure of the ceramic tool materials under various cutting conditions.
本文探讨了晶体材料的切削加工性，重点分析了切削条件对表面粗糙度的影响。
The machinability of crystal material is studied, and the influence of the cutting condition on surface roughness is analyzed.
采用灰色关联度分析方法识别不同切削条件下的主要误差源，并进行了实验验证。
The analyzing method of grey relativity is used for identifying main error sources under different cutting conditions, and these results are verified by experiments.
通过理论分析和试验研究，探讨硬质合金刀具在变速切削条件下磨损累积的规律。
With theoretical analysis and experimental research, the regularity of wear cumulation of carbide tools under varying cutting speed conditions is studied.
在高速切削条件下，材料的切削机理将发生变化，切削过程将变得容易，切削热将降低。
In this process the heat of cutting is reduced and the material can be easily cut.
本文根据实验观察，对高速切削条件下连续型带状锯齿形切屑的形成过程进行了分析研究。
Based on the experimental observation, the high speed formation courses of the continuous banding serrated chips are studied and analyzed.
本文根据实验观察，对高速切削条件下连续型带状锯齿形切屑的形成过程进行了分析研究。
Study on microscopic characteristics of adiabatic shear bands in the serrated chips formed during high speed machining;
加大插齿刀后角可以有效改善插齿刀的切削条件，提高齿表面加工质量和延长刀具使用寿命。
Enlarging the clearance of gear shaping cutter can improve efficiently its cutting condition, the gear surface quality and tool life.
试验证明，切削状态当量电阻能有效反映切削条件的变化，通过检测其变化可实现导电加热切削加热电流的最佳控制。
The experimental results show that cutting state resistance is an effective parameter for detecting the change of cutting conditions. As a result, the optimum heating current in elect...
以单因素实验法分别考察了刀具材料、冷却条件、切削深度、进给速度等对刀具磨损的影响规律。
In single factor test, the influencing factor of tools wear was discussed, such as tool material, cooling conditions, cutting depth and feed speed.
在磨粒磨损条件下，其磨损机制主要是显微切削、颗粒脱落和脆性剥落；
In the condition of abrasive attrition, the wear loss is mainly caused by micro-cutting, particle shattered and brittle micro-peeling.
通过传热学、流体力学、切削理论的综合运用对波形刃铣刀片温度场边界条件进行了研究。
The boundary condition of temperature field for waved-edge milling insert is researched based on the heat transfer, fluid dynamics and metal cutting theory.
自适应切削可以保证在加工条件不断变化的情况下使切削过程始终处于最佳状态。
The adaptive cut can make cut process at optimum condition all along, in case the machining conditions are constantly changing.
采用连续改变激光切削参数的方法，研究了切割条件对切口形状和尺寸的影响及切口控制方法。
An experimental study is presented to investigate the effects of cutting conditions on kerf geometry with variable process parameters.
本文应用李亚普诺夫直接法研究了切削过程中在机床结构刚度非线性条件下速度型颤振的动态稳定性问题。
Liapunov's Direct Method is used to solve the stability problem of the speed-type chattering occurring in machine tool during cutting.
本文应用李亚普诺夫直接法研究了切削过程中在机床结构刚度非线性条件下速度型颤振的动态稳定性问题。
Liapunov's Direct Method is used to solve the stability problem of the speed-type chattering occurring in machine tool during cutting.
应用推荐