本文给出用对称联系法解圆分度误差时。
In measuring circular indexing error with symmetry-relation method, the author tries to operate with a microcomputer.
对于分度台的工作分度误差与齿盘加工误差之间的关系进行了实验验证。
The relationship between the dividing error of the divider and the machining error of the serrated tooth discs has been found by experiments.
介绍一种用双自准直仪和多齿分度台组合测量静态测角分度误差的测量方法。
This paper introduces the method for the synthetic of measuring quiescing goniometry with two autocollimators and precise angle dividing table.
并结合实例，运用变形梯形加速度运动规律，通过微机计算，得出了该凸轮机构从动件的分度误差曲线。
With an example given, index error curve is obtained by applying acceleration law of deformed trapeze on a computer.
文章分析了在圆分度误差测量中应用谐波分析法处理数据的原理，同排列互比法相比，用此法可以减少检测工作量。
Data are processed by harmonic-analysis method in the error separation of circular division. This method can reduce the workload of inspection.
以啮合理论为基础，导出了蜗式凸轮机构从动件(即分度转盘)在凸轮实际轮廓和实际机构尺寸诸因素的影响下，分度误差的计算公式。
Based on meshing theory, a formula is derived for calculating index error of worm-type CAM follower (i. e. Tindex plate) under influence of actual worm-type CAM profile and dimensions.
介绍了在凸轮检测仪上应用计算机的辅助作用检测弧面分度凸轮廓面的方法，在此基础上介绍了误差分析方法。
The method of measuring globular indexing CAM contour with computer aid is introduced. effect of the CAM contour error on index error is analyzed.
选取适当的车头行星轮的分度圆直径，可以有效地控制车方原理的直线度误差。
The principle straightness error of cutting square in work-pieces can be controlled by choosing a suitable pitch diameter of the planetary gear in the machine tools.
介绍了一种对多齿细分分度台综合示值误差进行检定的简便方法，并进行了测量不确定度评定。
A valid verifying method of error of indication is introduced for subdivide multi-tooth table in this paper. The evaluation of uncertainty of measurement is given.
测量齿顶圆直径估算分度圆螺旋角，用分度头在铣床上修正分度圆螺旋角，并进行误差分析。
The spiral angle of graduated circle was rough estimated by measuring the addendum circle diameter and modified on milling machine.
讨论了多步法的原理、方法误差能及分度转台设计中的几个问题。
The principle and method error of the multi-step method and some design problems of the indexing table are also discussed.
为此，本文以弧面分度凸轮的轮廓面方程为基础，建立了弧面分度凸轮的三维模型，提出了一种用三坐标测量机测量其轮廓面误差的方法。
Therefore the author built a 3-d model based on the surface equations of roller gear CAM, and presented a method of using coordinate measuring machine (CMM) to measure the surfaces of the CAM.
本文介绍了这种算法的原理和实现方法，并在滚击机分度传动误差控制中得到成功应用。
The principle and applied method are intro duced and the algorithm is successfully applied to a gear hobbling machine.
本文介绍了这种算法的原理和实现方法，并在滚击机分度传动误差控制中得到成功应用。
The principle and applied method are intro duced and the algorithm is successfully applied to a gear hobbling machine.
应用推荐