本文对蒸发冷却技术的特点及多功能大容量蒸发冷却试验台进行了比较详细的论述。
The characteristics of evaporative cooling technology as well as multifunction testing stand of large-capacity are described in this paper.
通过交替加热及冷却试验测试该陶瓷涂层的抗热冲击性能，并与其他人的研究数据进行比较。
Resistance to heat shock of the obtained ceramic coating was tested by alternate heating and cooling experiments, and was compared with those obtained by other researchers.
热交换器。制冷剂冷却的液体冷却器。性能确定的试验程序。
Heat exchangers - Refrigerant cooled liquid coolers - Test procedure for establishing the performance.
在进行YZ 2003型振动压路机设计时，为使发动机水温和液压系统油温都获得最佳的冷却，对该机的散热系统进行了试验研究。
When designing model YZ2003 vibratory compactor, heat dissipating system was tested and researched in order to get best cooling for engine water and hydraulic oil of the machine.
通常，对流换热系数是在实验中以电加热试验管壁面后根据牛顿冷却定律计算得来的。
Normally, coefficient of convective heat transfer is gotten through experiments which is heating testing tube by electricity and computed through Newton cooling law.
然而，实验室条件下试验所达到的冷却速率在工业化生产中较难实现。
However, the cooling rate obtained in these tests was very difficult to do under the industrial scale.
本文阐述了在一台单缸直喷式柴油机上进行高温冷却模拟隔热试验。
Experiments of high temperature cooling simulating insulation were conducted on a single cylinder DI diesel engine.
进行三组敏感性试验，研究凝结潜热释放，蒸发冷却与地表热通量对气旋结构与强度的影响。
Three additional sensitive experiments are carried out to investigate the effect of condensation latent heating, evaporation cooling and surface heat flux.
采用激冷斜槽法和低过热法进行浇注料坯的试验，在试验中研究了不同浇注温度和冷却板倾斜角度对所浇注料坯的微观组织的影响。
The experience was conducted using cooling slope and low superheat processes, effects of pouring temperature and the degree of slope on the billet's structure were researched.
由拉伸和疲劳试验，测定了冷凝器用钛螺纹槽冷却管的力学参数；
The mechanical parameters of the cooling tube with spiral flute were measured by the tension and fatigue tests.
试验研究了开箱温度和冷却速度对低、高温时效型合金时效硬化效果的影响。
The effects of opening flask temperature and cooling rate on low and high temperature age-hardening alloy casting are tested and studied.
潜水服。第3部分：自动加热或冷却服装(装置)。要求和试验方法。
Diving suits - Part 3: actively heated or cooled suit (systems) - Requirements and test methods.
介绍了复合式气冷涡轮导叶的冷却效果试验研究。
This paper introduces the cooling effectiveness experiment research on a compound air-cooled turbine vane.
轴温度超过60度将进行冷却，由载荷决定试验终止，通过频率下降或转角增加终止试验。
Cooling is needed when temperature of driveshaft is over 60? C, judging by frequency dropping or rotating Angle increasing to end the test.
根据干熄炉内焦炭换热的特点，用干熄炉模型对焦炭粒度和冷却气体流量等参数进行了试验。
According to the feature of coke heat exchanging in CDQ chamber, the test on the parameters such as coke size and cooling gas flow was made with the CDQ model.
本文给出了一个冷却塔的配水模型试验结果。
This paper presents the model experimental results about the water distribution in a cooling tower .
本文对在淬火油槽内用超声波振动提高油冷却能力的试验进行了研究。
This paper deals with the experimental study of improvement on the oil cooling ability by producing ultrasonic wave vibration in the quenching oil trough.
根据试验研究情况，从刀具结构参数、钻孔冷却方式、加工工艺要点等方面详细介绍了高温合金孔的加工技术。
According to test research situation, machining technique has been presented in terms of cutter structural parameters, cooling method for drilled holes and machining technology.
介绍了汽车发动机冷却水泵密封性能试验台系统设计方法，实现汽车冷却水泵密封性能测试系统的自动化、智能化。
This paper introduced the system design methodology used for automobile water pump seal performance testing, and realized of automation, intelligent for testing it.
试验结果表明，改进后的冷却系解决了ZA6440轻型客车长期存在的发动机过热问题。
The test result shows the engine overheat problem long time existed in ZA6440 light bus has been solved by the improved cooling system.
通过不同冷却速率下的DTA试验研究了A357合金的凝固行为；
The solidification behavior of A357 alloy was analyzed by the DTA at various cooling rates.
给出了促使冷却池形成面流散热的工程设施和必要的试验数据。
Engineering installations and necessary data to impel cooling pond to form surface-flow for heat loss have been given.
进行微生物控制动态模拟试验，明确了废水回用于冷却循环水系统对系统的微生物的生长的影响。
The influence of the microbe growing of the coke plant wastewater reused to the cooling water system was clear by microbe controlling experiment.
本试验以化工废水经净化后拟作为工业用的冷却水为试验水，进行了加臭氧处理试验。
An experiment in which the purified wastewater of chemical production was treated with ozone and reused for industrial cooling water was conducted.
介绍了TSD09型摆式动车组冷却装置的任务来源、设计过程、冷却装置结构方案、运用的冷却技术、部件特点以及相关试验。
The structural scheme, design process, used cooling technologies, components features and relevant tests of cooling device for TSD09 tilting diesel multiple unit were described.
为了研究换热器间距对冷却组性能的影响，将某轮式装载机后置冷却组放在风洞试验台上进行测试。
To study the spacing effect on the cooling package performance, a rear mounted wheel loader's cooling package was tested on a wind tunnel test rig.
为了研究换热器间距对冷却组性能的影响，将某轮式装载机后置冷却组放在风洞试验台上进行测试。
To study the spacing effect on the cooling package performance, a rear mounted wheel loader's cooling package was tested on a wind tunnel test rig.
应用推荐