本文论述了不同碳含量碳素钢的组织形态与抗冲击磨粒磨损性能的关系。
This paper deals with the relation of the microstructure morphology of carbon steels to its impact abrasion resistance.
离心磨球的抗冲击磨损性能高于静力金属型磨球，并且在高冲击功条件下尤为显著。
The wear resistance of centrifugal cast grinding ball is higher than that of statically me…
利用单摆划痕法的冲击加载特性，研究了N i - P化学镀层的冲击磨粒磨损性能。
Impact abrasive wear behavior of electroless Ni-P coating was researched by means of single-pass pendulum scratching test characterized by impact loading.
这种双轴式离心冲击磨，在不提高离心盘转速的条件下就能加大物料间的碰撞力，粉碎效果好。
The twin shaft centrifugal impact grinding reinforces collision between the materials and the grinding effect is fine.
纳米级的磨粒冲击到工件表面，在以原子级去除的同时伴随着塑性变形的发生。
When abrasive grains impacted on the work piece surface, the top layer atomics are removed, plastic deformation appears at the same time.
冶金、矿山等行业所用湿磨机衬板的服役条件十分恶劣，既要承受冲击，又要承受腐蚀和磨。
Lining board used in the wet-grinding machine at metallurgical mines works under very bad conditions. It has to bear impact, corrosion and wear.
介绍用聚四氟乙烯粉填充于环氧胶中，研究了粉的含量对冲击强度、粘接强度、硬度、干磨性能的影响。
The content of PTFE powder filled in the epoxy adhesive can affect the impact strength, adhesive strength, hardness and dry-wear property of the adhesive.
文中指出，钢筘的失效是振动磨损、磨粒磨损、疲劳破坏和冲击损坏综合作用的结果，其中冲击损坏的危害作用最大。
The paper points out that reed failures result from the synthetical action of vibrating wear, grain wear, fatigue damage and last, impact action-the most dreadful damage.
在动载三体磨粒磨损条件下，试验研究了冲击载荷的变化对铸态复相耐磨钢动载磨粒磨损特性的影响。
The influence of varying impact energy on wear resistance of dual phase cast steel has been investigated under impact three body abrasion.
突出的特点是晶体尺寸小耐冲击，因用自磨机加工破碎，颗粒多为球状颗粒，表面干洁，易于结合剂结合。
Outstanding characteristic is impact resistance value because of the little crystal size, particle almost is spherical since the mill processing, the surface is dry and clean, and easy to bond.
产品性能：不破碎，耐研磨，硬度均匀，冲击值高，磨机综合效率高。
Performance: hardness uniform, not broken, ground resistance, the impact of high value, high efficiency integrated mill.
文中指出，钢筘的失效是振动磨损、磨粒磨损、疲劳破坏和冲击损坏综合作用的结果，其如十击损坏的危害最大。
The paper points out that reed failures are resulted from the synthetical action of vibrating wear, grain wear, fatigue damage and last. impact action - the most dreadful damage.
当磨机参数一定时，可根据计算的冲击功选择磨球材料，从而确定磨球的尺寸。
The ball material selection can be based the parameters of mill thereby working out the dimensions of mill.
得出岩石在受到磨料射流的冲击下，磨粒与水体对岩石的冲击压力与岩石在水介质作用下力学特性的变化共同促使了岩石的破坏。
It has been shown that the impact pressure and changing of mechanical characteristic of rock together make it broken by abrasive water jet.
仿真结果表明，应用文中提出的控制策略可减少离合器滑磨功、降低换挡冲击，有效地改善了换挡品质。
A simulation is conducted and the results show that the proposed control strategy can reduce the slipping friction work of clutch and shifting jerks, and hence effectively improve shifting quality.
磨球的冲击功与球磨机直径、转速、脱离角、磨球直径和材质有关。
Impact work of grinding ball depends on the diameter and revolutions of mill, the release Angle, diameter and materials of balls.
研究了冲蚀角度、冲击速度、磨粒尺寸、冲蚀时间等影响因素对材料的冲蚀率的影响。
The effects of impact Angle, particle velocity, erodent size and impact time were demonstrated.
最后，动力通过与齿型驱动轮适应的同步齿型带传输给所述冲击式磨机的所述转子。
Finally, power is transmitted to the rotor of the impact mill by a synchronous sprocketed belt, accommodated by a sprocketed drive sheave.
此外，所述冲击式磨机可以由分离的圆锥段形成。
In addition, the impact mill can be formed of separated conical sections.
冶金矿山湿式磨机衬板，使用工矿条件恶劣，既受腐蚀又受冲击和磨损。
The liner of the wet-grinding machine at metallurgical mines works under very bad conditions, and it has to bear impact, corrosion and abrasion.
所述转子配备有多个冲击刀，所述多个冲击刀与设置在所述磨机外壳的内部顶面的多个冲击刀互补。
The rotor is provided with a plurality of impact knives complementary with a plurality of impact knives disposed on the inside top surface of the mill casing.
用微观组织分析、杆盘式磨损、湿磨法磨损和冲击韧性等试验手段，对高铬铸铁衬板的显微组织、力学性能和耐磨性进行了试验分析。
Failure analysis of high chromium cast iron liner has been studied by the microstructure, pole-pan wear abrasion, wet grinding and impact toughness.
立柱、摇臂、摆臂和磨辊等是辊式磨的主要部件之一，在物料粉磨的过程中受到的动载荷、冲击载荷作用。
Column, rocker, roller, etc. are ones of the main components of roller mill, in the process of grinding materials, they are affected by dynamic loads and impact loads.
立柱、摇臂、摆臂和磨辊等是辊式磨的主要部件之一，在物料粉磨的过程中受到的动载荷、冲击载荷作用。
Column, rocker, roller, etc. are ones of the main components of roller mill, in the process of grinding materials, they are affected by dynamic loads and impact loads.
应用推荐