研究贝氏体相变的特点,弄清贝氏体相变反应与共析分解的区别极为重要。
It is important to understand the difference of bainite transformation and eutectoid decomposition in steels.
高于此点,由于超过共析点钢完全由珠光体和退火状态的渗碳体组成,硬度增加并不多。
Above this point the hardness can be increased only slightly, because steels above the eutectoid point are made up entirely of pearlite and cementite in the annealed state.
钢中珠光体转变属典型的扩散型共析转变。
Pearlitic transformation in steel is a typical diffusion eutectoid transition.
熔敷金属组织主要是针状铁素体,少量的先共析铁素体。
Microstructure of the deposited metals is composed of acicular ferrite and a little proeutectoid ferrite.
熔敷金属组织主要是针状铁素体,少量的先共析铁素体。
The microstructure is composed of acicular ferrite and a little proeutectoid ferrite.
应用电子衍衬技术和扫描电镜等手段,对共析珠光体轨钢的微观结构和断裂过程,进行了观察和分析。
The microstructure and fracture process of an eutectoid pearlitic steel have been observation and analysed by means of electron-diffraction-contrast technique and SEM.
其成分特征是碳含量在共析点左右的高碳低锰钢轨钢。
The main characteristics of the rail steel are low manganese and high carbon which content is being closed to eutectoid.
共析分解是个自组织过程,具有铁素体和渗碳体互为领先相的整合机制。
The eutectoid decomposition is a self organization process, which is characterized by the integrated mechanism that ferrite and cementite acted as prevenient phase alternatively.
由于超过共析点钢完全由珠光体和退火状态的渗碳体组成,因此高于此点硬度增加并不多。
Above this point the hardness can be increased only slightly, because steels above the eutectoid point are made up entirely of pearlite and cementite in the annealed state.
结果表明,对于亚共析钢,在中温区变形、保温后可使先共析铁素体和珠光体组织大大细化,显著改善钢中铁素体和珠光体的分布状况;
The results show that, in hypoeutectoid steels, deformation at medium temperature may fine the structure and improve the distribution of ferrite and pearlite greatly;
含碳量少于共析体(低于0.77%)的钢称为亚共析钢。
Steels having less than the eutectoid amount of carbon (less than 0.77%) are known as hypo-eutectoid steels.
作为结果的组织结构是初步的共析铁素体(在共析反应前的铁素体)和部分珠光体的混合物。
The resulting structure is a mixture of primary or pro-eutectoid ferrite (ferrite that formed above the eutectoid reaction) and regions of pearlite.
如图2.1所示的简化铁碳状态图将焦点集中在共析区,这对理解钢的性能和处理是十分有用的。
A simplified diagram, such as the one in Fig. 2.1, focuses on the eutectoid region and is quite useful in understanding the properties and processing of steel.
此处理方法对必须机加工的过共析钢特别有用。
This treatment is particularly useful for hypereutectoid steels that must be machined.
硼有加速珠光体成长率的作用,无论在亚共析或共析钢中皆有同样的现象产生。
It was found by experiments thatboron increased the growth rate of pearlite, both in hypoeutectoid and eutectoid steels.
含碳量少于共析体(低于0.77%)的钢称为亚共析钢。
Steels shaving less than the eutectoid amount of carbon (less than 0.77%) are known as hypo-eutectoid steels.
最后讲述了珠光体生长的台阶机制及一些非铁碳合金的共析组织。
At the last, the steps mechanism of pearlitic growing and some eutectoid structures of non Fe-C alloys are pointed out.
锌铝共析合金具有良好的超塑性,但通常需要经过预变形(轧制或锻压)来得到。
Usually, excellent Superplasticity of Zn-Al eutectoid alloy could be obtained by pre-deformation (rolling or forging).
研究了两种基体的亚共析钢经激光处理后,其硬化层的硬度梯度及其磨损特性。
The hardening gradient and the character of abrasion in hardening layer of hypoeutectoid steel with two kinds of matrixes that was treated by laser beam have been studied.
由于恰好高于低临界温度通常使过共析钢奥氏体化而硬化,所以对外层采用较低的热处理温度。
The lower heat-treating temperature of the case results from the fact that hypereutectoid steels are normally austenitized for hardening just above the lower critical point.
为了准确地检验高碳过共析钢盘条中的网状渗碳体,分别对选用硝酸酒精溶液侵蚀和碱性苦味酸钠水溶液热侵蚀两种显示方法进行了比较。
In order to detect the carbide network in high carbon hypereutectoid steel wire rods accurately, two kinds of detection method of the carbide network are compared.
扫描电镜观察表明,加入铝,可抑制锻后空冷条件下先共析网状碳化物的析出;
The microstructure analysis by SEM showed that the precipitation of netlike proeutectoid carbide has been inhibited during air cooling after forging due to Al addition to the UHCs.
结果表明,随冷却速率的增大,先共析铁素体的晶粒尺寸减小,体积分数增大,针状铁素体增多;
The results show that with the increase of cooling rate, the grain size of proeutectoid ferrite decreases, the volume fraction of proeutectoid ferrite and acicular ferrite increases.
过共析钢是含碳量大于共析量的钢。
Hypereutectoid steels are steels that contain greater than the eutectoid amount of carbon.
采用因子分析法评价量表的结构效度,共析出2个公因子,对总方差的贡献率分别为57.6%,12.0%。
The validity was assessed by factor analysis and 2 factors were obtained, which accounting for 57.6%and 12.0%of the total variance, respectively.
提高退火温度,尤其是在高于共析温度退火有助于加快块状组织的分解过程。
With the increase of annealing temperature, the decomposition process of massive microstructure will be accelerated.
本文是针对塑压模的热处理变形控制的研究。特别是对亚共析钢制塑压模更为有效。
This paper mainly researches on the control of heat treatment deformation of plasticpressing mould, the method is especially effective to the mould made of hyposteel.
本文是针对塑压模的热处理变形控制的研究。特别是对亚共析钢制塑压模更为有效。
This paper mainly researches on the control of heat treatment deformation of plasticpressing mould, the method is especially effective to the mould made of hyposteel.
应用推荐