通过举例说明在聚酯变形工艺中最佳的假捻器入口温度。
The article analyses the best inlet temperature of false twister in polyester distortion technique by examples.
结果表明：总温升随入口温度的降低而近似线性地升高。
The model shows that total temperature jump almost increases linearly with decreasing entry temperature.
适当提高尾气入口温度、加强工艺管理和采用渗铝板进行包补是防止腐蚀的有效措施。
Properly increasing the furnace inlet temperature, strengthening the process management and selection of aluminum diffused plates could effectively protect the corrosion.
表1含有进行系统热量测量时散热器基座测试点或空气入口温度应该低于的推荐温度值。
Table 1 contains the recommended temperature that the heatsink base test point or the air inlet temperature should remain below during the thermal evaluation of a system.
当二次空气的入口温度低于一次空气的露点温度时，一次空气的冷却有可能是一去湿过程。
When the entering temperature of the secondary air is lower than the dewpoint temperature of the primary air, there may be a dehumidifying cooling pro-cess in the primary air passages.
同时考虑闭式循环水系统中冷却塔对循环水入口温度的影响，确定出循环水泵最优运行方式。
Cooling towers' influence on the inlet temperature of circulating water was also considered to determine optimum running mode of circulating water pumps.
结果，轧机的入口温度较高，实现了在给定的精轧出口温度较低，以及在奥氏体范围内更薄的压力表。
As a result, higher mill entry temperatures, lower mill exit speeds at a given finishing temperature and thinner gauges in the austenite range could be realized.
通过实际运行证明，本控制系统使其入口温度稳定在设定值附近，取得了较好的控制效果并确保了干燥质量达到生产指标要求。
It is proved that the control system makes temperature steady near the enactment value in working, guarantees the dry quality reaching required production target.
这可以让原子的温度下降几百华氏度—比你想放入口中的任何东西都要冷得多—在不足一秒内。
This drops an atom's temperature a couple hundred degrees fahrenheit-much colder than anything you'd want to put in your mouth-in less than a second.
逐渐打开温度较低的产品流上的入口隔断阀。
Gradually open the inlet block valve on the coolest product stream.
关闭温度较低的产品流上的入口隔断阀。
逐渐打开温度较高的产品流上的入口隔断阀。
关闭温度较高的产品流上的入口隔断阀。
其后方能入口，而且泡制时间的长短，水的温度，茶具的讲究都有许多学问，最重要的是，喝茶之人应懂得如何品尝它的味道！
Later in order to import, and in preparing the length of time, water temperature, tea sets of knowledge about many, the most important thing is that the tea should know how to enjoy the taste of it!
结果表明：玻璃屋入口流速对室内及多孔墙内空气的温度场与流场有较大的影响。
The result shows that the inlet velocity has significant influence on the temperature field and flow field in glass house.
提出了一种考虑轴向热传导、速度滑移、温度跳跃和入口效应情况下圆形微通道能量方程的求解方法。
A method for resolving the energy equation of the circular microchannel, which considers axial heat conduction, temperature jump, velocity slip and thermal entrance is presented.
分析了副槽入口风速等参数对转子温度分布的影响。
The effect of inlet velocity of fluid on temperature distribution was analyzed.
结果表明入口蒸汽压力和过冷水温度是影响汽羽形状的主要因素。
The results indicated that the shape of steam plume was influenced by the inlet steam pressure and subcooled water temperature.
分析研究了温度、入口惯性效应等因素对漏气量的影响。
The influencing factors, such as temperature and entry domino effect, were analyzed.
从入口冲洗温度较低流体侧，使热交换器与管道中没有水。
Flush the coolest stream inlet to blowdown or pumpout system to water free the line and exchanger.
从入口冲洗温度最高流体侧，使热交换器与管道中没有水。
Flush the hottest stream inlet to blowdown or pumpout system to water free the line and exchanger.
从入口开始到中间它们的意思越来越深刻的，就像温度一样越来越难接受。
Starting from outside their meaning gets more and more indiscreet and unbearable as we close in on the center, where the temperature as-well has become unbearable.
在不同车速行驶工况下对二行程轻便摩托车用尾气催化剂的入口及中心温度进行了测量与分析。
The inlet temperature and internal temperature of exhaust catalyst for two stroke moped are tested under different vehicle driving speed.
屏幕同时液晶显示冷水出口、冷水入口和设备设定温度。
Liquid crystal display showing temperatures of outlet and inlet chill water-provides visualized and direct setting.
通过测试进入风扇入口的空气温度可以提供更多一般的评估。
A more general evaluation can be done by testing the temperature of the air entering the fan inlet.
经过分析后认为，入口处反应油气管温度下降幅度较大是造成反应油气入口结焦严重的根本原因。
Analysis result shows that the great temperature decrease in reaction oil and gas pipe inlet is the main cause.
在固体燃料冲压发动机性能分析基础上，推导了某发动机的推力和比冲与入口流量和温度之间的关系式。
The relations of thrust and specific impulse to inlet air flow and temperature are derived from theoretical analysis of solid fuel ramjet (SFRJ) performance.
并探讨了入口气流温度变化对鼻腔内气流温度分布的影响。
The influence of the change of airflow temperature in the entrance on the temperature distribution in the nasal cavity was also discussed.
温度控制装置在工厂就预先设置，并且按照电路图所示进行布线，固定在热水器顶部面板入口内。
Thermostats are factory set and wired in accordance with the wiring diagram fastened to the inside of the top access panel.
计算采用典型F GD入口烟气参数，应用烟气湿度和定压容积热容的概念计算了吸收塔出口烟气温度及塔内蒸发水量，并分析了其变化规律。
With adoption of the typical flue gas inlet parameter for FGD, this article completes above calculation with humidity and pressure volume heat concept, and analyzes the relative changing rules.
应用推荐