光耦，光电晶体管输出，基地连接。
漏血检测器光耦插头。
本设计方案阐述了一个简单改进光耦电路的方法。
This Design Idea describes a method of improving the simple optocoupler.
光耦也有优势。
光耦器件用于串行口、开关量输出等回路时也存在上述现象。
The paper concludes that the "transient saturation" phenomenon can happen when optocouplers are used in serial communication port and binary output port.
通过管理芯片和周围空气之间的热传递，维持光耦特性，避免失效。
Sustain an optocoupler's performance and avoid failure by managing the heat transfer between the chip and the ambient atmosphere.
通过管理芯片和周围空气之间的热传递，维持光耦特性，避免失效。
Sustain nan optocoupler's performance and avoid failure by managing the heat transfer between the chip and the ambient atmosphere.
该装置的电路由脉冲形成源、压频变换器和光耦与功率开关三部分组成。
The circuit of this device is formed the source, pressed frequently by the pulse changer, photosensitive resister and power switch three parts make up.
该系列相机所有型号都包含PoE（以太网供电），三光耦输出，以及64兆图像缓存。
All models include PoE, three optocoupled outputs, and a 64 MB image buffer.
随着光耦元件在综合自动化变电站二次设备中的广泛应用，其工作特性也需要引起特别关注。
Along with the extensive application of optocoupler element in the secondary equipment of integrated automatic substations, its operating characteristic also needs much attention.
针对目前电气隔离器件状况，提出基于高精度线性光耦hcnr201的电压、电流测量电路。
Introduced are measuring circuits of voltage and current based on HCNR201, high-precision and high-linearity optocoupler, after surveying different kinds of current electrical isolators.
为了准确客观地检测出爆裂噪声的存在，提出了基于噪声信号奇异性的光耦器件爆裂噪声检测方法。
In order to detect the presence of burst noise in optocoupler device accurately and objectively, a new method was put forward based on singularity of noise.
针对电流小信号采集中存在噪声干扰的问题，采用高线性度模拟光耦hcnr 201设计了电流信号隔离采集板。
Aiming at the noise jamming problems in acquisition of small current signals, an isolation and acquisition board for current signal is designed based on HCNR201 high-linearity analog optical coupler.
控制器驱动外部NPN晶体管的射极，并与变压器串联构成反激式拓扑，系统通过变压器和光耦实现离线式的要求。
It drives the emitter of an external NPN transistor, and series with transformer to consist a flyback topology. The system is offline through the use of transformers and optocoupler transistor.
介绍了IRIG-B码对时的概念、IRIG-B码对时模块的组成，其组成部分包括微处理器、电平转换器件、光耦隔离器。
The paper introduces the time synchronization conception of the IRIG-B format code and its module constructions which include microprocessor, level converter and optically coupled isolator.
此肌电放大器的前置部分采用共模驱动，以达到提高其共模抑制比和输入信号的动态范围，以及抑制工频干扰等作用，并采用线性光耦隔离。
Apart from employing the linear optocoupler isolation, this EMG pre-amplifier uses the boost to enhance the CMR and the input swing and reject the industry interference.
在系统的硬件设计中，处理器采用TMS320LF2407数字信号处理器（DSP）；逆变器采用智能功率模块（IPM），并采用高速光耦对其驱动。
In the area of hardware design, the system uses TMS320LF2407 DSP as microprocessor, and uses intelligent power module (IPM) as inverter, which is drived by high-speed optocouplers.
在系统的硬件设计中，处理器采用TMS320LF2407数字信号处理器（DSP）；逆变器采用智能功率模块（IPM），并采用高速光耦对其驱动。
In the area of hardware design, the system uses TMS320LF2407 DSP as microprocessor, and uses intelligent power module (IPM) as inverter, which is drived by high-speed optocouplers.
应用推荐