用等效力学模型法研究了多腔体充液晃动问题。
Using the equivalent mechanical model, this paper investigated multi-tank liquid sloshing problem.
根据试验数据拟合出合理充液率的经验关系式。
Based on experimental data, empirical correlation on filling ratio was obtained via regression.
可见对于某一给定的充液比，存在两个临界频率。
It is known that there are two critical frequencies for a given fill ratio.
本文介绍一种新型的可靠的密封—充液膨胀停车密封。
This paper introduces a new and reliable seal, a stop seal filled with liquid.
软组织肿块或片状病灶内可见支气管充气、充液征象。
The bronchi filled with gas or fluid were soft tissue mass or sheet lesion.
本文分析并计算了部分充液球形贮箱内的液体晃动问题。
In the paper, the liquid sloshing in a partially liquid-filled spherical tank is investigated.
充液过多会使蒸发器内供液过多，有溢回压缩机的危险；
Too much filling for the liquid within the evaporator will too, has the danger of overflow back to the compressor;
本文系统地研究了平底和球面圆筒形件充液拉深成形精度。
The forming accuracy of flat and round bottomed cylindrical shells formed by hydraulic counter pressure deep drawing is investigated.
目的：观察体外循环中预充血定安对预充液胶体渗透压的影响。
Objective:To observe the effect of Gelofusine for colloid osmosis pressure(COP) during cardiopulmonary bypass.
理论分析得到了带粘弹性包覆层充液管道中纵向模态的频散曲线。
Our theoretical analysis produces the dispersion curves of longitudinal modes of ultrasonic guided waves in liquid-filled pipes with viscoelastic coatings.
主机部分包括机身、主缸、压边装置、顶出缸及充液装置等组成。
The mainframe includes the body of machine, main cylinder and press edge fitting, and cylinder of pack out and filling liquid equipment etc.
受外激励的充液刚性容器中流体的波动问题有实际的工程应用背景。
The free surface responses of a fluid in a rigid fluid-filled container due to external excitation have many engineering applications.
本文采用试验研究的方法，给出了一种较佳的工作介质及其充液率。
The work fluid filling amount in the thermosyphon is studied, and the optimal work fluid and filling amount are presented by means of the experimental study.
在脉动热管稳态运行的情况下，充液率的增加使得传热热阻不断增加；
The increasing of charging ratio make the thermal resistance increasing on the PHPs's steady-state operation.
由于密封破裂出于安全考虑，宜谨慎测试毛细管充液和工艺介质的反应。
For safety consideration due to ruptured seal, reaction of capillary fluid with process fluid should be carefully examined.
从理论上分析了各向同性弹性介质中有限长充液圆柱壳的自由振动特性。
The axisymmetric vibration characteristics of finite length fluid-filled cylindrical shells in elastic medium are analyzed systematically in theory.
本文利用交结构控制理论的原理研究了全充液飞行器的大角度操纵问题。
The liquid-filled spacecraft large-angle maneuver problem is investigated using the principles of variable-structure control theory.
在研究的范围内，最佳充液率和最佳倾角随加热水流量的增大均有所增加。
Within the range of the study the optimum liquid-filling rate and the optimum inclination Angle will be somewhat greater when the heating water flow rate undergoes an increase.
复杂充液航天器的晃动及其对控制系统的影响是当前空间高技术的重要问题。
Sloshing of Complex Liquid-filled spacecraft and its influence on the control systems are the recently significant problem in the space technology.
本文讨论当部分充液转子受到任意的侧向位移扰动时作用在转子上的扰动力。
This paper discusses disturbing forces on a partially liquid-filled rotor when it is subjected to arbitrary lateral displacement.
考虑了具有弹性底板的部分充液的有限长方形容器内的液体的耦合晃动问题。
This paper studies the coupled oscillations of liquid in a partially-filled container of finite size and having an elastic bottom and rigid walls.
在本文中，提出了充液罐的设计的方法，并对液压系统的设计作了详尽的计算。
In this paper, It new way of the design of surge tank is presented, and some related calculations of the hydraulic system design are given in detail.
分析了热管的启动特性以及热流密度、蒸发段倾角和充液率对其传热特性的影响。
The effect on heat transfer performance caused by heat flux, gradient and liquid-filled ratio of evaporation end was deeply investigated.
蓄能器充液阀是一种用于工程机械及矿山无轨设备制动液压系统的关键液压元件。
Accumulator charging valve is key unit used in hydraulic braking system of engineering machinery and rubber tyred equipments for mines.
弹性介质刚度不仅对充液圆柱壳的实固有频率影响显著，而且影响其截止轴向模态。
The rigidity effect of surrounding elastic medium is remarkable not only to the real characteristic frequencies of cylindrical shells but also to the cut-off axial mode.
利用机械臂调整多刚体航天器姿态的算法，在必要的修正后可以用于充液航天器调姿。
Revised algorithms of attitude regulation of rigid spacecraft using manipulator moving can be used for liquid-filled spacecraft.
采用LB46型液力变矩器为基型作计算仿真，得出了液力变矩器部分充液输出特性。
Calculation simulation is conducted with model LB46 hydraulic torque converter as a basic model and output characteristics of the partially filled converter are obtained.
介绍了法兰连接式充液阀的原理和设计要点，并介绍了安装使用的方法及应注意的问题。
Principle and design keys of a flange type filling valve have been introduced with methods of installation and use as well as issues deserved notice.
介绍了法兰连接式充液阀的原理和设计要点，并介绍了安装使用的方法及应注意的问题。
Principle and design keys of a flange type filling valve have been introduced with methods of installation and use as well as issues deserved notice.
应用推荐