1987年，霍诺顿在“元分析”中研究了数百项自动超感官知觉全域测试的结果，这种分析是一种统计方法，旨在从一系列研究中得出全面的结果。
In 1987, results from hundreds of autoganzfeld tests were studied by Honorton in a "meta-analysis", a statistical technique for finding the overall results from a set of studies.
概率元分析是由切斯特于1934年提出的。
利用大型有限元分析软件Msc。
图9：RUP计划中的zachman元分析。
弹性力学基本方程正确的弱形式将是有限元分析的基础。
The correct weak form of basic equations in elasticity is the foundation of finite element analysis.
而ANSYS是得到广泛应用的大型通用有限元分析软件。
And ANSYS is a large scale general finite element analysis software with abroad application.
这个元分析提供了一个有用的概览，包括提升目前证据的问题。
This meta-analysis provides a useful overview, including raising issues with the current evidence.
建立了利用物元分析理论进行湖泊水质富营养化评价的新模型。
A new model for assessment of water quality eutrophication of lakes was established by using matter element analysis theory.
对有限元分析的基本过程及非线性有限元原理进行了简要介绍。
The basic process of FEM and the principle of nonlinear element method are simply presented.
有限元网格生成是零件几何定义和有限元分析之间必不可少的步骤。
Mesh generating is a necessary procedure between geometric definition of part and its finite element analysis.
那么，首先，我应该注意到原始研究的首席作者并不必然赞同这份元分析的研究。
Well, first of all, I should note that the lead author from the original study does not necessarily agree with the findings of this meta-analysis. From the NYTimes coverage
所得结果与通过有限元分析所得的锻造过程中局部张力及温度进行对比。
The results were compared with the local values of strains and temperatures during the forging process predicted by the finite-element program.
本文主要介绍对已完成基本结构设计的气缸缸套精磨外圆夹具的有限元分析。
This text mainly introduces a way of Finite Element to analysis the fine whetting outside circle of urn about the tongs.
通过元分析150种实验和10万参加者，男性在冒险的16个种类中的14种占绝对优势。
In a large meta-analysis involving 150 studies and 100,000 participants, in 14 out of 16 categories of risk-taking, men were over-represented.
详细讨论了基于有限元分析的钢筋混凝土和预应力混凝土楼板的板带截面设计方法。
The section design method of slab strips for reinforced concrete and post tensioned concrete slabs is discussed in detail.
元分析结果显示，有14%的研究者曾见过自己的同事杜撰、伪造、改动或修改数据。
The meta-analysis suggested that 14% of researchers had seen their colleagues fabricate, falsify, alter or modify data.
法内利发现，有18项调查符合他的元分析标准，而在他的综述中，也引用了其他一些调查结果。
Dr Fanelli found 18 surveys that met the criteria for his meta-analysis, and a few others that he also included in a general review.
他搜索出以往关于科学诚信的调查，然后利用一种所谓的元分析技术(荟萃分析)对其进行分析。
He hunted down past surveys of scientific honesty and subjected them to what is known as a meta-analysis.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
同时分析了有限元分析误差产生的种类及原因，并对自适应单元网格优化进行了研究。
The category and reason for Finite Element Method analysis error are analyzed, and the adaptive mesh method is researched.
最后在单元上计算和引入剪切修正系数，再经过有限元分析计算出全局响应的修正值。
Finally, the shear correction factor for each element was estimated and the global response corrector was calculated by the incorporating shear correction factor.
本文利用有限元分析软件LS - DYNA对金属板料渐进成形的过程进行了模拟。
In this thesis, by using FEM software-LS-DYNA, we simulate the process of sheet metal Incremental Forming.
通过非线性有限元分析，计算出焊点疲劳寿命对下部填充料基本热力学性质的依赖关系。
Through non-linear finite analysis , the dependence of fatigue life of solder joint on thermomechanical properties of underfill was calculated.
本文结合工程实例，对楼板的温度裂缝进行了有限元分析，并提出了一些预防裂缝的建议。
In this thesis based on engineering examples, some Suggestions were put forward to control crack by finite element analysis of floor slabs.
针对石窟文物的特点，阐述了影响石窟围岩变形稳定性的主要因素和动力有限元分析方法。
Considering characteristics of grotto relics the influence factors and dynamic finite element analysis methods on deformation stability grotto country rock are discussed.
通过对四种二次曲线截面的柔性铰链的理论计算和有限元分析，比较分析了它们的力学特性。
Theory calculate and finite element method to symmetric conic-section flexure hinges is used to compare and analyze their dynamics characteristic.
有限元分析证实，最低程度的切除骨和韧带能够更大程度的保留术后腰椎正常活动范围32。
A finite element analysis demonstrated that minimizing bone and ligament removal resulted in greater preservation of normal motion of the lumbar spine after surgery32.
分析结果显示，将基于有限元分析的优化技术应用于非标零件的设计是一种非常可行的方法。
The analysis result shows that it is a very feasible method for designing of nonstandard parts to adopt optimal technology based on finite element analysis.
分析结果显示，将基于有限元分析的优化技术应用于非标零件的设计是一种非常可行的方法。
The analysis result shows that it is a very feasible method for designing of nonstandard parts to adopt optimal technology based on finite element analysis.
应用推荐