介绍了深度误差允差的计算方法及计算结果。
The calculation method and results of the tolerance of error in depth for diffraction pattern are shown.
皮带输送机称重系统的技术规定、允差和技术要求。
Bait Conveyer Weighing System Technology Tolerance and Technology Request.
允差，有时会跟公差混淆，但其具有完全不同的含义。
Allowance, which is sometimes confused with tolerance, has an altogether different meaning.
选用焊接技巧应保证不超出指定的直线度和圆度允差。
Welding techniques shall be selected to ensure that specified tolerances for straightness and out-of-roundness are not exceeded.
单向体系允许在依然保留相同允差或配合类型的情况下改变公差。
The unilateral system permits changing the tolerance while still retaining the same allowance or type of fit.
为了使配合零件之间具有过盈或强制配合，公差必须产生零或负允差。
To have an interference or force fit between mating parts, the tolerances must be such as to create a zero or negative allowance.
计算值全部落在1985年公布的国际水蒸气骨架表的允差范围以内。
All the calculation values fall under the allowance range of the international water vapor skeleton table published in 1985.
所采用的制造工艺和使利润最大化的最小生产及装配成本都要求给定公差以保持所需允差。
Both must be given tolerances in keeping with the allowance desired, the manufacturing processes available, and the minimum cost of production and assembly that will maximize profit.
提出了对彩色胶片进行颜色测量时所用的红色、绿色和蓝色峰值位置，半波宽度和峰值允差。
The corresponding peak value position, half band-width and peak value's allowance of Red, Green and Blue of color measurements of color negative films are provided.
在确定大屏幕空间显色恒定性允差后，可用文中提供的方法对制作大屏幕的LED进行筛选。
Given the allowance of space colour constancy, the riddling of LED for large screen display can be made using the method.
分别使用镁砂灰皿和骨灰灰皿，样品含Au量的分析结果与理论含Au量的偏差均在国家标准的允差范围内；
Respectively using magnesium oxide and bone ash cupels, the result deviation of gold content in the samples is within the allowable deviation of the national standards.
根据设计要求之制动减速度和制动力分配比，提供摩擦系数计算方法和顺序，用于合理确定台试时的摩擦系数允差。
According to the design requirements of braking deceleration and distribution proportion between braking forces of front and rear wheel, a procedure of calculation for friction factor is provided.
超出合同允差的多装部分买方有权拒收；超出合同允差的少装部分按其货值金额(按合同价计算)的15%赔偿给买方。
The Buyer is entitled not to accept the part exceeding the contract tolerance weight the Buyer shall be compensated at 15% of the value (calculated at the contract price) of the short part.
超出合同允差的多装部分买方有权拒收；超出合同允差的少装部分按其货值金额（按合同价计算）的15%赔偿给买方。
The Buyer is entitled not to accept the part exceeding the contract tolerance weight and the Buyer shall be compensated at 15% of the value (calculated at the Contract price) of the short part.
超出合同允差的多装部分买方有权拒收；超出合同允差的少装部分按其货值金额（按合同价计算）的15%赔偿给买方。
The Buyer is entitled not to accept the part exceeding the contract tolerance weight and the Buyer shall be compensated at 15% of the value (calculated at the Contract price) of the short part.
应用推荐