用摆线对渐开线齿轮齿形进行修形。
提出齿廓修形曲线应满足的条件。
The conditions to be satisfied for profile modification curve are suggested.
齿面修形是提高齿轮副啮合性能的重要手段。
The modification of gear is a principal method for improving performance of meshing.
提出了一套斜齿轮修形用的有限元计算程序。
A computer program is worked out for modification design of helical gears by using Finite Element Method (FEM).
该方法较适合单件、小批量修形齿轮的加工。
The method is adapted for machining single piece or small lot relief gears.
齿面修形是提高齿轮副啮合性能的重要手段。
The modification of gear is a principal method for improving performance meshing.
介绍数控技术在绝缘子修形设备改造中的应用。
Introduce the application of numeric control technique in rebuilding equipment of the insulator form repair.
齿面接触分析结果表明失配修形后接触质量良好。
The tooth contact analysis shows that good modification effect is achieved when the method of tooth mismatched modification is used.
分析了工艺修形的机理，并介绍了其在生产中的应用。
The author had analyzed principle of this technology, then discussed its application in gear production.
本文提出了ZC_1蜗杆传动可控修形的理论和方法。
This paper gives the theory and method of the controllable modification of ZC_1 worm drive.
提出对角修形的最佳修形量计算公式。给出一个计算实例。
The calculation formula of optimal diagonal modification value is presented. A calculation example is given.
本文运用复合形法解决了直廓环面蜗杆各种修形的参数优化。
The parameter optimization of various general type is achieved by applying compound form method.
用途：主要用于水晶甲、玻璃甲、树脂甲片的抛磨及修形。
Uses: Mainly used for crystal A , GiassA, a piece of cast resin grinding and modification.
直齿廓环面蜗杆或者二次包络环面杆蜗，均需进行修形加工。
It is necessary for both straight profile toroid worm and double enveloping toroid worm to be pruned on the faces of teeth.
研究了螺旋锥齿轮齿面综合研磨率、动态互研与研齿修形机理。
The material general removal rate and the dynamic mechanism of tooth surfaces modified and corrected mutually during lapping process of hypoid gears were firstly investigated.
推导出了活齿端面谐波齿轮各啮合副经过齿面修形后的齿面方程。
The equations of teeth surface after modification of all key components, such as wave producer, oscillating teeth, end face gear, are deduced.
静态计算结果表明，直齿锥齿轮齿廓长修形具有较好的减振效果。
The result of static calculation showed that the tooth profile long modification of spur bevel gear possesses better effects of vibration reduction.
根据修形原理，建立了约束条件和数学模型，实现了修形的优化。
According to the principle of the general-type, constraint condition and mathematics pattern are established, realized the optimization of the general type.
细分曲线曲面的可局部修形性，对NURBS细分算法的研究等。
The problems include modifying the local shape for subdivision curves and surfaces, the subdivision schemes for NURBS etc.
齿轮强度分析是轮齿承载能力、振动、噪声及修形等研究的基础。
On the basis of analysis of gear teeth strength, gear power capacity rating and profile correction, as well as vibration and noise of gearing, are studied.
因此本文对渐开线斜齿圆柱齿轮的修形方法及修形量进行进一步探讨。
So this article research on the involute helical gear modification method and modification of the amount.
齿轮弯曲强度分析是轮齿承载能力、振动、噪声及修形等研究的基础。
The gear bending strength analysis is a foundation in research, such as gear power capacity rating, profile correction, as well as vibration and noise of gearing.
由修形后传动副的接触状态分析可见，传动副对误差的敏感性已大大降低。
Thus it can been seen that, after mending tooth shape of the worm, the Wildhaber-worm gear pair sensitivity to errors has been greatly reduced.
介绍了成形砂轮磨齿机的几种齿形修形方法及混合修形技术在工程上的应用。
In this article, the method and application of mixed flank modification in gear profile grinding machine are introduced.
通过试验得出通电电流和加工时间是控制修形量和修形长度的两个基本参数。
Test result indicates that both current and processing period are principal parameters to affect the volume of crown.
修形直齿轮因误差因素在齿对的啮入和啮出位置会出现啮合干涉或啮合间隙。
Errors of modified spur gears results in meshing interference or meshing clearance at the position of mating teeth coming into or out of contact.
本文从弹流角度分析了修形前后线载荷分布及最大压力沿接触线的变化规律。
In this paper, the varying rules of the linear load distribution and the largest stress along the contacting lines are analyzed based on the EHL theory.
在ANSYS软件中建立了标准渐开线齿轮与修形齿轮的动力接触有限元模型。
The dynamic contact finite element models of standard involute gear and modification gear are established in the software of ANSYS.
用齿面接触分析法求解了存在制造误差时修形传动的齿面接触状态和运动精度。
The tooth contact and kinematic precision of the modified worm gearing with manufacturing errors has been investigated by the TCA method.
用齿面接触分析法求解了存在制造误差时修形传动的齿面接触状态和运动精度。
The tooth contact and kinematic precision of the modified worm gearing with manufacturing errors has been investigated by the TCA method.
应用推荐