文章介绍了机器人施釉主控软件系统的设计与实现。
The paper introduces the design and realization of the main control software system of the robot glazing system.
现有的电视跟踪测量系统的主控软件的一个很突出的问题是代码的重用性和扩充性差。
A outstanding problem in control software of TV follows the measuring system at present is it is hard to reuse and extend the code.
文章提出采用TMS320 LF 2407为主控芯片，介绍了系统总体方案设计、硬件设计、软件设计、并给出了详细的实验步骤和实验数据分析。
The system USES TMS320LF2407 as major control chip, introduces system main scheme design, hardware design, software design, and gives detail experimental procedure and analysis of experimental data.
实现了图像采集卡与GPIB仪器集成，完成了测试系统的主控软件。
Realized the integration of the frame grabber card and GPIB instruments, completed the test system host controls software.
在本系统监控软件实现过程中，使用了四个MCGS组态窗口，它们分别是设备窗口、实时数据库窗口、用户窗口、主控窗口。
In the process of control system 's monitor software realized, we used four MCGS SCADA Windows. It is made up of Device Windows, Real-Time databank Windows, Users Windows and Main control Windows.
给出了以89s52为主控芯片的下位机系统的软硬件设计，并给出了上位机操作软件和与下位机的通信协议。
The software and hardware design of the substrate control system which USES 89s52 as the main control chip, the PC's operating software and the communication protocols are given in this paper.
该系统由前端传感器、电压匹配电路、主控制器和事故后处理软件组成。
The system is composed of sensor, the circuit of voltage matching, main controller and dealing software.
初始化配置子模块负责正确配置像质测量系统的硬件，并根据主控制模块传入的参数进行对应的软件设置。
The initial configuration sub module configures the hardware of the imaging quality measuring system via software and transfers the parameters from the main control module to software configuration.
本文主要介绍逆变电源的分析和该ups逆变系统的硬件设计和软件设计，主控制芯片采用TMS320F240。
This dissertation chiefly introduces the analysis of this inverter power and the design of hardware and software of this UPS, and the core control chip is TMS320F240 which is produced by ti corp.
阐述了系统的总体结构和工作原理，重点论述了如何利用组态王设计和实现系统中的主控软件部分。
This paper illustrates the whole structure and principle, and describes how to design and realize main control software of system by using KingView.
介绍了系统PLC主控制器I/O端口设计，系统硬件组成和系统软件中主程序及自动加工子程序设计；
The I/O design of PLC controller, the hardware configuration and the main routine and auto-machining subroutine of software program are presented.
设计了基于软件握手的人机交互系统通信协议，可以实现与主控板的准确、快速通信。
The second is the design of the communication protocol between the H-M interface and the main control board, which is based on the software handshaking.
系统采用SPCE061 A微控制器为主控单元，特别指出了软件设计中需注意的几个问题，最后利用软件对实验数据进行误差修正。
SPCE061A MCU is adopted as central control unit. Especially, we point out several problems which must be paid attention to in the program, and correct the error of experiment data in the end.
同时对控制系统的软件流程进行了设计，其中主程序是主要完成遥控状态与自主控制状态之间的相互切换。
Meanwhile, the design of the program is mentioned briefly. The main program is the shift between two control states: remote control and autonomous control.
其次，根据设计要求，进行底层运动控制系统硬件电路和软件程序的设计，主要包括了主控制器电路和电机控制电路。
Then the circuit and program of on-board motion control system are designed according to the needs, including chief MCU circuit and motor control circuit.
本人参加了上述第一个项目软件无线电系统的整体设计，完成了主控与基带信息处理模块的硬件设计、部分软件设计调试，以及第二个项目的主控与基带处理单元模块的调试、最终完成整机调试和指标测试。
The thesis expounds the cell design and timing design of the FPGA circuit in main controlling and baseband signal processing module, and develops the hardware of it, and programs part of the software.
本人参加了上述第一个项目软件无线电系统的整体设计，完成了主控与基带信息处理模块的硬件设计、部分软件设计调试，以及第二个项目的主控与基带处理单元模块的调试、最终完成整机调试和指标测试。
The thesis expounds the cell design and timing design of the FPGA circuit in main controlling and baseband signal processing module, and develops the hardware of it, and programs part of the software.
应用推荐