上压板与连接块顶部固定在一起，并将同步齿形带压紧。
The upper platen is fixed together with the connecting block, and compacting the synchronous toothed belt tight.
复合式弯辊液压缸缸体的上、下端分别装有上压板和下压板组成油缸，里面装有活塞杆和连接杆。
Upper and lower ends of the hydro-cylinder identity are installed upper pressure board and down pressure board, which has piston rod and connecting stick.
本试验机操作方便，上压板空间调节采用自动升降，检测结果数字显示，可直接打印结果，并可与电脑联网。
The examination machine is easy to operate and the upper board space adopts auto ascend and has data display result. It can print and connect with computer.
一种烤架（20）包括具有下烤制表面的下压板组件（22）和枢转连接 且具有上烤制表面的上压板组件（24）。
A grill (20) includes a lower platen assembly (22) having a lower grilling surface and a pivotally attached upper platen assembly (24) having an upper grilling surface.
每天的压顶操作中，在进行抗压试验前，应对至少三个试样上压板的平面度进行检查，这些试样是随机抽取的，分别代表操作开始、中间和结束时所用的试样。
During each day's capping operation, check the planeness of the caps prior to compression testing on at least three specimens, selected at random, representing the start, middle, and end of the run.
现代古巴三明治一定要在三明治压板上烤到奶酪融化为止。
A modern Cuban sandwich is always toasted in a sandwich press until the cheese melts.
平压机：小型活版印刷机。纸张摆稳于压板上，然后压向垂直的装版台的机器。 收藏。
Platen: Small letterpress printing machine on which the paper is held in the platen and pressed up against the vertically-held type-bed.
定期清洁机台表面、底板及下模滑板、沟槽、上模内压板及保险杆(注：必须关闭电源并恢复常温)。
Clean the machine including the surface, base, slip board, groove, pressed board and oriented pole in the fixed time. (turn off the power until the machine to normal temperature).
独特的气动压板装置，电磁阀控制真空吸附台面，上料准确、高速、效率高。
Unique pneumatic clamp device, the electromagnetic valve control vacuum table, feeding accurately, high-speed, high efficiency.
在分析总结现有的橡胶坝螺栓压板式锚固和楔块挤压式锚固方法的基础上，提出了伸缩锚固方法。
Based on the summarizing and analyzing of the traditional boltplaten and wedge-squeeze anchoring methods of rubber dam, the extension-type anchoring method is introduced in this paper.
在内端盖与机座的连接 处法兰上铣一个与轴承盖上所铣平面位置相对的槽，槽内放置测速传感器；将 轴头压板改为齿盘结构。
A groove is milled on the flange for installing the speed sensor at the junction of the inner end cap and the seat, which is facing to the plane on the bearing cap.
在内端盖与机座的连接 处法兰上铣一个与轴承盖上所铣平面位置相对的槽，槽内放置测速传感器；将 轴头压板改为齿盘结构。
A groove is milled on the flange for installing the speed sensor at the junction of the inner end cap and the seat, which is facing to the plane on the bearing cap.
应用推荐