吸入装置包括吸入液面至泵进口处的管路、阀件等。
The suction facilities include the pipeline from the suction fluid surface to the inlet of the pump and valves and fittings.
利用功率键合图的理论,建立了关键阀件的数学模型,分析了系统的性能。
Mathematical models of the key valves are established by using the Power Bond Graphtheory, and system performances are analyzed.
控制元件:为满足传动性能的需要,在系统内为控制压力,流量和方向等而配置的各种阀件。
Control components: in order to meet the needs of transmission performance, in the system for the control of pressure, flow and direction of the configuration of various valves.
泵阀件采用带导向杆的半球形柱塞结构,弹簧制动,精确控制阀球与阀座对中,启闭动作及时。
The pump valve has a structure of semi-spheric plunger with guide rod, and its seat and ball are aligned by means of a spring, and it is opened and closed in time.
该项包括在线仪器、流量计、调节阀、紫外光、泵、泵的密封件、过滤膜、垫圈和密封材料以及其他特殊的在线设备。
This would include in-line instrumentation, flow meters, regulating valves ultraviolet lights, pumps, pump seals, filter membranes, gasket and seal materials, and other specialized in-line devices.
配备所需长度的阀杆延长件,可以对某个蝶阀进行远程操作。
Stem extensions can BE furnished to permit remote operation of butterfly valves in any required length.
论述了陶瓷内件控制阀的研制,该阀内件同时具有耐腐蚀、耐磨损(包括冲刷、气蚀)与耐高温的性能。已获得成功应用。
The control valves with ceramic trim are expounded. It has the corrosion-proof, abrasion-proof and high temperature proof performance, and it also has obtained successful application.
采用具有更小流量的通径更小的截止阀或V形阀内件截止阀,可能使得阀门能够具有更大的开启度,因此可以避免损坏。
Use of smaller valves or V-Port trim with lower flow capacity may permit the valve to be open at a greater percentage, thus avoiding damage.
对于真活接球阀、止回阀和隔膜阀,在上底漆和粘固剂连接之前,先拆卸活接头螺母和端口连接件。
On True union Ball, Check and Diaphragm valves, remove union nuts and end connectors before priming and cementing connections.
介绍了应用这两个软件进行阀类零件三维图形绘制、拼接与组合的基本技巧。
The basic skills for using these two software to draw, join and fit together three-dimensional figures of accessory valves were introduced.
由于工作条件相当恶劣,压裂泵的易损件——阀的使用寿命相当低,甚至于不足以完成一次作业(约2.5小时)。
Under the severe operating conditions, the life of its quick-wear parts, valves, is too short to accomplish one run (about 2.5 hours).
通常用作蝶阀的阀内件。
歧管可以只是机械零部件或是完整的组件,包括止回阀,压力开关,伺服阀,电磁阀或过滤器。
Manifolds can be either machined components only or complete assemblies including check valves, pressure switches, servovalves, solenoids or filters.
包括“建筑五金、船用五金、球阀、泵阀及机械零件”等。
The company's products include building hardware, marine hardware, ball valves, pump valves and machinery parts.
它主要由内筒、外筒、带有单向阀的活塞、溢流件、调节环,密封圈等组成。
The leakproof hydraulic damper is mainly composed of an inner cylinder, an outer cylinder, a piston which is provided with one-way valves, overflow members, adjustment rings, seal rings, etc.
针对反应堆的特殊要求,主氦循环风机的设计包括总体结构、叶轮型式、冷却系统、轴承、测量仪表、电气贯穿件和隔断阀。
The design of the helium circulator involves the overall construction, the impeller type, the cooling system, the bearings, the instrumentation, the electrical penetrations, and the shutoff valve.
利用阀控泵-马达同步系统可以保证旋压机两个旋轮的同步精度,以保证旋件的质量。
The synchro accuracy of two spinning wheels of spin forming machine can he obtained by using the synchro system of valve controlled pump-motor, therefore the quality of workpiece is ensured.
重锤锁气翻板卸灰阀主要由阀体、阀板、阀轴、摇杆、重锤等零件组成,利用力矩平衡的方法实现锁气卸灰。
The valve is mainly made up of body, disc, axle, rocker and heavy hammer etc. It realizes discharging and air locking using trimming moment.
泵阀是钻井工作过程的直接组成件,也是钻井泵中最重要的易损件之一。
Drilling pump valve is one of the most important wearing parts of drilling pump.
摘要针对闸阀阀杆填料密封泄漏的问题,提出了正确选择密封填料的材料和改进闸阀填料压盖密封件结构的技术改进措施。
In allusion to the leaking of packing of gate valve, this paper presents technical improvement measures in properly selecting packing material and varying the structure of packing assembly.
形端口阀内件截止阀比塞形阀瓣或球形阀瓣截止阀具有更加线性的节流曲线,但是,所有这些类型的截止阀都不建议连续用于严格的节流应用中,这种情况可能需要采用控制阀。
V-port trim has a more linear throttling curve than plug or ball discs, but none of these trims are recommended for continuous severe throttling which may require using a control valve.
不需要从管线上拆卸阀门,即可拆卸、维修或检查阀内件。
Internal parts can be removed, repaired or inspected without removing the valve from the piping.
一些结构由两件式阀盖和轭架组成。
CPVC封装的阀杆加长件并不用于水平球阀系列。
CPVC housed stem extensions are not intended for the horizon ball valve series.
备用密封件是阀帽(12)内主阀杆密封组件(20)的二级密封。
The backup seal is secondary to the main stem seal assembly (20) in the bonnet (12).
一旦传感器输出偏离最初预期阀瓣末端位置值时,用户就可以立即检测到磨损密封件。
The user can thus detect a worn seal as soon as the sensor outputs a value that deviates from the originally expected flap end position.
穿过阀帽的通道(34)可用于检验通过这种密封件是否泄漏。
A passage through the bonnet (34) may be used to test for leakage past such seal.
阀盘处于打开位置时,密封件长轴大于阀盘直径,且相互不接触。
When the disc is in the open position, the seal major axis is greater then the disc diameter and they do not touch.
铸青铜阀体和连接端口,防吹出硅青铜阀杆或316不锈钢球体和阀杆为选配件(66阀内件)。
Cast bronze body and end piece, blowout proof silicon bronze stem or 316 stainless steel ball and stem are optional (66 trim).
铸青铜阀体和连接端口,防吹出硅青铜阀杆或316不锈钢球体和阀杆为选配件(66阀内件)。
Cast bronze body and end piece, blowout proof silicon bronze stem or 316 stainless steel ball and stem are optional (66 trim).
应用推荐