尺蠖驱动器按锁模机构分类。
Inchworm actuators are classified by the clamping mechanism.
能容易改变锁模激光器的输出参数。
It is very easy to change the output parameter of mode locked laser.
输出锁模脉冲的基频为几兆赫兹。
注塑生产中，锁模力参数设计十分重要。
Clamp force parameter setting is very important in plastic injection molding.
本文对被动锁模激光器的涨落模型作了改进。
The fluctuation model of passively mode-locked lasers has been improved.
本文给出了钩子锁模闭式挤压新型模具结构。
A new type of structure of closed extrusion dies with locking hooks is put out.
合模快速，且有低压安全锁模装置，保护模具。
Feel fast jointly, and there is mould device of low-voltage safety lock, protect the mould.
合模快速，且有低压安全锁模装置，保护模具。
Shut the mould fast, and have mould device of low-voltage safety lock, protect, the mould.
锁模不仅可用损耗调制取得，也可用位相调制来得到。
Mode locking can be induced not only by loss modulation, but also by phase modulation.
边缘温度的突然下降是产生锁模不稳定性的重要标志。
The drop of edge temperature is an important feature of appearance of the locked mode instability.
理论分析了利用非线性偏振旋转效应锁模激光器的机理。
The physical mechanism of nonlinear polarization rotation mode-locking was analyzed in theory.
由此，对这类混合锁模激光器系统的特性作了理论解析。
Based on these results, some characteristics of such a hybrid mode-locked lasers system are interpreted theoretically.
预测可能存在的气泡位置及锁模力的大小，确定最佳浇口位置。
In order to obtain the best gate location addition, the position of air bubble and the clamp force were forecasted.
预测可能存在的熔接痕位置及锁模力的大小，确定最佳浇口位置。
In order to obtain the best gate location addition, the position of weld lines and the clamp force were forecasted.
对于均匀展宽激光器的非线性镜锁模，提出了一种解析分析方法。
This paper presents a closed form analysis method of nonlinear mirror mode lo-cking of a homogeneously broadened Laser.
鉴于锁模力的理论计算较为复杂，本文提出了一种简化的计算方法。
Because the theoretical calculating method of clamp force is very complex, a simplified experiential calculating method is provided.
它采用主-被动锁模相结合的染料激光脉冲与碘激光脉冲同步工作。
The dye laser pulse has been synchronized with the iodine laser pulse by a combination of active-passive mode-locking.
在相应于谐波锁模、有理数谐波锁模条件下得到了稳定的脉冲输出。
Steady pulses were obtained on harmonic and rational harmonic mode-locked status.
利用产生最有效锁模的腔参数及涨落模型，进行了激光过程的数值模拟。
Taking the cavity parameters providing a most efficient mode locking and based on fluctuation model, we performed a numerical simulation of laser operation.
本机合模装置属液压式结构，主要由导柱、动模板、支承板、锁模油缸等组成。
This device adopts hydraulic structure and is mainly made up of guide pole movable platen support plate and clamping cylinder etc.
利用克尔透镜锁模自启动条件，对常用的四镜腔激光器的启动特性进行了系统分析。
The starting characteristics are theoretically analyzed according to the self-starting condition of Kerr lens mode locking.
设计了伞齿轮完全闭塞式锻造的模架，核心部位刚性锁模机构具有良好的闭模特性。
A typical die set for closed-die forging has been designed, of which the core rigid close-die mechanism has a good property.
提出了一种新型的分步有限差分(SSFD)算法来求解非线性锁模脉冲传输方程。
A novel numerical algorithm SSFD (split-step finite difference) has been presented for solving nonlinear pulse propagation equation.
分析了相位偏置和光纤的色散对锁模机制的影响，获得了产生稳定超短光脉冲的条件。
The effects of phase bias and group velocity dispersion on mode locking mechanism are analyzed. The operating conditions for stable short pulse generation are obtained.
我们都知道对于相应的产品投影面，如果没有足够的锁模力的话，可能会有飞边产生。
We all know that if you don't have enough clamp force for the projected area of the parts, flash will result.
如果排气口的确存在，尺寸合适并且干净，那么减少锁模力会有助于排气，并使注塑更快。
If vents do exist, and they are properly sized and clean, then reducing the locking force can help with venting and enable faster injection time.
对主动锁模光纤激光器的锁相环进行改进，提出一种新型的“变带宽锁相环”的设计结构。
This article presents a new design structure of variable bandwidth phase-locked loop based on improving phase-locked loop of actively mode-locked fiber laser.
在自锁模钛宝石激光器中，除可形成传统的单脉冲外，在适当的条件下，还可产生双脉冲。
Besides the conventional single pulse train generation, the ti: sapphire laser system sometimes produces two or even more pulses should proper conditions be satisfied.
用傅里叶变换的方法分析了锁模激光器中模式间的相位和振幅涨落对锁模脉冲列特性的影响。
The Fourier transform method has been used to analyze the influence of modal amplitude and phase fluctuations in a mode-locked laser on performance of its output pulse.
用傅里叶变换的方法分析了锁模激光器中模式间的相位和振幅涨落对锁模脉冲列特性的影响。
The Fourier transform method has been used to analyze the influence of modal amplitude and phase fluctuations in a mode-locked laser on performance of its output pulse.
应用推荐