目前，经济实用的钨极氩弧(TIG)焊接方法是应用最为广泛的焊接方法之一。
At present, tungsten inert gas (TIG) welding method is one of the most widely used methods for its advantages of economy and convenience.
钛合金车架采用无氧钨极氩弧焊接工艺。
介绍了钨极自动氩弧焊在不锈钢复合管生产线上的应用。
The application of automatic TIG welding on stainless steel compound pipes production line is introduced.
本文介绍一种新型钨极脉冲氩弧焊机，分析了基本工作原理及技术性能。
A new type of argon tungsten pulsed arc welding machine has been introduced in this paper. The basic operating principle and technical characteristics has been analyzed.
本文介绍一种新型钨极脉冲氩弧焊机，分析了基本工作原理及技术性能。
A new type of argon tungsten pulsed arc welding machine has been introduced in this paper.
针对高压空气环境的特殊性，研制了高压焊接试验舱和钨极氩弧自动焊机。
Aiming at special demands under high air ambient pressures, this paper developed the hyperbaric welding test chamber and the automatic GTAW machine.
通过钨极氩弧焊试验，对焊接热影响区温度场进行分析和研究，建立了焊接热循环曲线。
The temperature field in welding HAZ was studied and analyzed. Welding heat curve was set up by argon-shielded tungsten arc welding experiment.
介绍采用药芯焊丝手工钨极氩弧焊焊接奥氏体不锈钢管道所进行的焊接试验及工艺评定。
The welding experiment and procedure qualification for manual TIG welding of stainless steel tubes with flux cored electrode is presented in this paper.
答：钍钨极仍是直流焊最常用的钨电极。但许多人开始避而远之，因为该元素具有放射性。
A: They remain the most common tungsten used in DC applications, but many people are starting to shy away because of the element's radioactivity.
利用ABAQUS有限元软件对铝合金平板钨极氩弧焊(TIG)焊接过程进行了数值模拟。
The simulation of aluminum alloy plate tungsten inert gas welding (TIG) process using finite element software-ABAQUS was researched.
此外，在焊接试验的基础上，进一步对双钨极氩弧焊降低电弧压力、减少焊接缺陷的机理进行了分析。
In addition, the mechanism of the T-TIG arc pressure reduction to make the sound weld formation was analyzed.
对补焊工艺方法的选择作了比较，具体阐明了采用手工钨极氩弧焊的补焊工艺方法，实践证明，效果良好。
The selections of repair welding technology are compared, and the repair welding technology using handwork gas tungsten arc welding is detailed. The result with good effect is got.
针对造成双弧现象的原因，模拟分析了由于电流过大、喷嘴压缩孔径过小和钨极偏心三种因素所导致的双弧现象。
The phenomenon of double arc which is usually caused by the reasons of too big welding current, too small diameter of the nozzle and eccentric of the cathode has been simulated.
结果表明，在一定的焊接工艺条件下，使用钨极氩弧焊和与母材同质的焊丝，可以对ZA12材料进行有效的焊接。
It is shown that under suitable welding condition, the alloy can be welded well by using TIG arc welding and the welding wire having the same composition as the alloy.
采用模拟时的焊接工艺参数进行钨极氩弧焊平板对接焊，测定焊接热循环曲线和焊缝截面尺寸，对模拟结果加以验证。
The welding thermal cycle and section dimensions of the welding seam were measured in the condition of the simulated welding process parameters for checking simulation results.
试验采用钨极氩弧焊对接焊形式对BT 20钛合金施焊；焊接接头的塑性变形试验在油压机上进行，变形过程中采用了双保温措施。
BT20 titanium alloy is welded with butt welding on GTAW machine... Experiment of plastic deformation is done on press and double heat preservation measure is used during plastic deformation.
并通过一系列焊接工艺试验，确定采用管子内缩管板和高铬镍焊材及自动脉冲钨极氩弧焊方法，提高了管子管板的焊接质量和可靠性。
A series of welding process testing showed that using recessed tube-tube sheet, high Cr-Ni welding materials and automatic TIG welding technology could improve the welding quality of tube-tube...
在氨饱和器焊接中采用钨极氩弧焊与焊条电弧焊相结合的焊接方法，重视焊前清理和焊接线能量控制，既保证焊接质量又提高生产效率。
Applied GTAW and SMAW to weld Ammonia Saturator with emphasis on preweld treatment and controlling welding heat input, high welding quality and efficiency were reached.
探讨了氦气和氩气不同配比对AZ31 镁合金交流钨极惰性气体保护焊（TIG）焊接性的影响，对不同气体配比的混合气体电弧特性、熔深、焊缝成型进行了分析和测定。
The influence of He-to-Ar ratio in AC-TIG on the AZ31 welding properties was studied. The arc characters, weld penetration, joint forming were measured and analyzed.
新的无爆破采矿工艺的诞生为开采黄金、钨、钼等贵金属薄矿脉和极薄矿脉开辟了一条途径。
The new mining method can reduce losses and dilution of excavated ores to extreme extent (<1~3%), while saving explosive materials.
新的无爆破采矿工艺的诞生为开采黄金、钨、钼等贵金属薄矿脉和极薄矿脉开辟了一条途径。
The new mining method can reduce losses and dilution of excavated ores to extreme extent (<1~3%), while saving explosive materials.
应用推荐