LN - 10半自动送丝机配有分开的焊丝导向装置，该装置能精确地排列焊丝，同时使焊丝顺利通过整个送丝系统。
The LN-10 semiautomatic wire feeder features the revolutionary split wire guide which precisely aligns and supports the wire through the entire feeding system.
采用数字化控制技术对送丝电机进行控制。
Adopting digital control technology controlled the wire feeding motor.
注：送丝速度及焊接电压设置范围与配套焊接电源相关。
Note: the wire feeding speed and the welding voltage are dependent on the selected welding power.
注：送丝速度及焊接电压设置范围与配套焊接电源相关。
Note: the wire feeding speed and welding voltage set range are dependent on the selected welding power.
参数控制包括焊接电流，焊接速度，送丝速度，保护气。
Parameter controls for welding current, travel speed, wire speed and shielding gas.
电源线和焊接电缆构成电源回路，为送丝机和控制系统提供电能。
The power cord and welding cable were used to provide power to the wire feeder and control system.
本文介绍一种SCR整流埋弧自动焊机电源及送丝控制，单片机应用系统。
The SCR Rectifier Auto-SAW power source and wire feeder with single chip computer control is introduced in this paper.
本文介绍了一种永磁式直流力矩电机驱动的动态品质优异的函数送丝系统。
The excellent dynamic characteristic function wire feed system driven by a permanent-magnet DC moment motor is described in this paper.
而送丝速度的调节快慢除了受控于实际的控制系统外，还受电机惯性的影响。
But the adjustment speed of wire feeding is subjected to the actual control system and the motor inertia.
这大大减小了电机的惯性，将其用于送丝系统将有望提高电弧电压的稳定性。
The stability of arc voltage may be improved by H-bridge driving circuit used for wire feeding system.
研究了焊丝端头小球对引弧成功率的影响； 研究了慢送丝对引弧效果的影响；
The effect of tiny ball at wire tip on the successful rate of arc striking and the effect of the wire slow feeding on striking result are studied.
送丝调速系统由功率MOSFET开关控制电路、脉宽调制电路及控制电路构成。
The wire feeder timing system consists of MOSFET switch control circuit, PWM circuit and control circuit.
主要产品有悬臂送丝机、吸烟手臂、自动化打磨专用设备、自动化焊接专用设备。
The main products include cantilever wire feeder, smoking arm, automated polishing equipment, automated welding equipment.
该送丝电路符合模块化的电路设计思想，能够较好的与数字化主控电路实现同步。
The feeder circuit meets the demands of modular structure, and it can meet the needs in synchronism with the main control circuit.
通过对二氧化碳焊机送丝系统的电路分析，论述了焊机的自动送丝和手动送丝原理。
The article discusses the automatic and manual feeding concept of the welding machine through analyzing the circuit of the wire feeding system of the CO2 arc welding machine.
实验发现，在送丝速度给定的情况下，匹配合适的电源电压可得到较好的焊接效果。
It has been shown by experiments that the good welding effects can be obtained by matching proper voltage of power supply when a certain feeding wire speed is given.
与该焊枪相关联的几个技术特征有：自动更换钨电极、双气流喷嘴和推拉丝送丝机构。
Several technical features are associated to the new torch design such as an automatic electrode change, a double flow gas nozzle and a push pull wire feeder.
由控制电路实现焊接程序的控制，带电枢电压负反馈的调速电路控制和调节送丝速度。
The control to welding procedure is realized by a control circuit, and wire feed rate is regulated and controlled by speed governing circuit with the armature voltage negative feedback.
送丝速度通过两个PI调节器进行双闭环控制，分别进行电枢电压反馈和电弧电压反馈。
Two PI adjustors were applied for wire feeding velocity control, one performed motor armature voltage feedback, the other one executed arc voltage feedback to determine the given velocity.
送丝速度通过两个PI调节器进行双闭环控制，分别进行电枢电压反馈和电弧电压反馈。
Two PI adjusters were applied for wire feeding velocity control, one performed motor armature voltage feedback, the other one executed arc voltage feedback to determine the given velocity.
标准的双程序转换开关允许操作者设置不同的电压和送丝速度，并在两种程序间相互转换。
Standard dual procedure allows operator to set different voltage and wire feed speeds and switch between the two.
在一些对电弧电压、电弧电流要求很高的焊接场合，目前常用的送丝系统将难以满足要求。
In some welding cases of high requirement to arc voltage and arc current, the usual wire feeding system is unable to meet the needs of wire feeding at present.
焊机运行过程中，送丝电机或焊接小车会出现无规则涌动现象，使焊接过程难以正常进行。
In the welding machine processing, the feeding wire moto or welding tractor will appear the non-rule surges phenomenon, which will cause the welding difficult.
型送丝机构采用永磁直流电机作为驱动元件，结构简单、实用，适用于抽头式焊机配套使用。
MXN-10-D wire feeder is designed with magnet motor as its drive, advantages; usefulness and suppleness, suitable for TAP-TYPE welding machine.
同模拟控制方式相比，数字控制方式可以采用更加灵活多样的控制算法来对送丝系统进行控制。
Compared with the simulant control manner, the digital control manner can adopt much more agile control algorithms to control the feeder system.
本文针对高质量板材对接填丝激光焊的需要，设计了对缝间隙宽度检测的传感器与送丝控制系统。
To guarantee good quality of butt laser welding with filler wire, a gap width detecting sensor and a wire feeding system has been designed.
采用波形控制方法对熔滴过渡周期进行控制，同时软件还对时序系统和送丝速度进行精密渐变控制。
The droplet transfer cycles were controlled by wave control method. Also gradual adjustment of the sequential and wire feed rate was controlled by software.
然而，市售的H桥电机驱动模块主要针对低压电机而设计的，难以直接用于埋弧焊送丝电机的控制。
However, it is difficult that the commercial H-bridge motor driver module designed for low voltage motor is applied to wire-feed motor of SAW directly.
然而，市售的H桥电机驱动模块主要针对低压电机而设计的，难以直接用于埋弧焊送丝电机的控制。
However, it is difficult that the commercial H-bridge motor driver module designed for low voltage motor is applied to wire-feed motor of SAW directly.
应用推荐