研究了加肋腹板连续组合梁的横向连接刚度和强度。
The strength and stiffness of continuous composite beams with stiffened web are investigated.
计算了单层单跨框架在竖向荷载下弯矩系数和连接刚度系数的函数公式。
The formulas of moment coefficient and connective stiffness coefficient single with the single span-layer frame under vertical loads are presented.
分析结果表明：翼缘削弱型刚性连接具有较大的连接刚度和理想的耗能性能；
The results of analysis indicate that the flange weakening type rigid connection has bigger connection rigid and better behavior of absorbing earthquake energy.
分析框架的内力系数和梁的连接刚度系数之间的关系，和影响它们关系的因素。
The relation between the internal force coefficient and connective stiffness coefficient of beam is studied and also the factors that affect the relation.
应用特征方程反问题的直接方法对舵面-液压伺服机构连接刚度参数进行了辨识。
The parameter identification of joining stiffness of rudder hydraulic servo mechanism can be done by using the direct method of characteristic equation anti problem.
探讨具有水平连接刚度突变特征的钢筋混凝土结构的一般力学特点与动力反应分析方法。
General mechanic differences and methods of dynamic response analysis of RC structure characterized by abrupt change in horizontal connection stiffness are discussed.
高强度螺栓端板连接是钢结构连接的主要方式之一，具有施工方便、承载力高、连接刚度大等特点。
Bolted end-plate connection is one of the main connection for the steel structures, which is with high resistance ability, large stiffness, and convenient for construction.
研究表明，涡轮泵不对称以及发动机与机架之间连接刚度弱是引起推力偏心和基频固有频率偏低的主要原因。
It is shown that the offset of propulsion force and the lower natural fundamental frequency are caused by asymmetry of turbopump and weakness of connection stiffness between propulsion and frame.
由若干部件经一定的连接部件组成的复杂结构系统，其连接部件的连接刚度可通过参数识别的方法来提取。
The stiffness of the connection joint which connect different parts of a complex structure can be extracted by identification method.
结果表明，木结构的榫卯连接刚度随荷载变化而呈非线性变化，刚度在0.3062 ~ 23.6054之间变化。
It is shown that the stiffness change of the mortise-tenon joint is nonlinear from 0.3062 to 23.6054 with the change of load.
研齿过程中机床主轴系统的设计以及主要工艺参数的选择是影响研齿效果的重要因素。通过主轴系统的动态分析，可以解决电机与主轴间连接刚度的选择以及飞轮尺寸的选择问题。
The important factors which affect the gear abrasion are the design of machine tool's spiale system and the selecting of main process parameters in the course of the gear abrasion.
第七个锚朝向天花板而没有物理连接，它的增加使得沿着表面的双曲率最大化，因而嵌入了内在刚度。
A seventh extra anchor toward the ceiling, not physically connected, is added in order to maximize double curvature along the surface, and therefore embedding inherent stiffness.
通过对与柱子相连接的弦杆的转动约束刚度进行修正，近似地考虑了与柱子相邻的桁架节间构件的约束作用。
The paper also approximately considers the restraints from the members of neighboring truss, by modifying the rotating restraint stiffness of chords connecting the columns.
由于该机床的主轴与机座之间为多杆并联连接，大大提高了机床的刚度，加工质量也有了较大改进。
Because PMT's principal axis is connected with machine base in multi-poles parallel structure, the rigidity of PMT and quality of process are improved.
先从梁柱节点受弯变形的机理入手，推导出钢框架梁柱焊接连接节点的初始刚度计算公式。
The formula calculating the initial stiffness of welded connection of steel frame was drawn according to bending deformation mechanism of joint zone of welded steel frame.
采用连接单元法，考虑连接柔性的影响，推导出半刚性框架梁柱的刚度矩阵及半刚性梁的固端弯矩。
The stiffness matrix of semi-rigid steel frames and the fixed end moment are deduced, based on the connection element method incorporating the effects of joint flexibility.
本文提出了半刚性连接钢框架位移和内力计算的刚度矩阵法，另外还提出了在水平荷载和竖直荷载作用下内力的简化计算方法。
Displacement of stress-resultants computation technique of semi-rigidly connected steel frames inclucing stiffness matrix method, hand calculation method has been proposed.
因为理想的刚节点和铰接点是不存在的，任何连接形式的刚度都是介于理想刚接和完全铰接之间的。
Because the ideal "rigid joint" and "hinged joint" are inexistent, the stiffness of any connection types is between ideal rigid joint and hinged joint.
因为理想的刚节点和铰接点是不存在的，任何连接形式的刚度都是介于理想刚接和完全铰接之间的。
Because the idealistic "rigid joint" and "hinged joint" are inexistent, the stiffness of any connection types is between idealistic rigid joint and hinged joint.
曲线表明，大部分的连接模型都呈现延性破坏，连接的强度和刚度都随板件的厚度以及连接件直径的增加而增大。
And the curves show that most models present ductile failure, and the connection strength and stiffness increase with the thickness of the plates and the diameter of the connection.
在转换层附近、塔楼与裙房连接附近以及设备层附近结构刚度有不同程度的突变。
Lateral stiffness of the structure varies significantly near the transfer floor, between the podium and the upper towers and near the story containing equipment.
研究结果表明：在弹性工作阶段，消能节点将木梁、柱连接成具有较大抗侧刚度的框架体系；
The results indicate that the timber columns and beams can be connected to form an assembled frame with high lateral stiff frame at elastic stage.
最后通过连接子结构刚度矩阵建立的平衡方程求解相应的刚度参数。
The stiffness parameters could be calculated from the solution of an equilibrium equation, through the stiffness matrix of the joint substructure.
由于采用栓接连接方式，以及拉杆本身的刚度，张拉力在离张拉点较远一端衰减的很快。
Due to the form of joint and the rigidity of rod, tension descends greatly on far end.
开孔板连接件是用于钢与混凝土结合的新型连接件，具有很大的抗剪刚度、强度及抗疲劳性能。
The perforated plate connector is a new type of connector used for steel and concrete composite structure and is characteristic of very great shearing rigidity, strength and fatigue behavior.
受压翼缘混凝土板的应力随着时间的增加而减小，但减小的幅度随剪力连接件的刚度增加而减小。
The concrete slab stress of the pressed flange decreases with the increment of time. But the diminished stress value decreases with the increment of the shear connector rigidity.
弹性连接和粘滞阻尼器提高结构刚度与阻尼以减小结构地震响应。
The links and viscous dampers increase the stiffness and damping ratio to cut down the seis mic response of bridge.
弹性连接和粘滞阻尼器提高结构刚度与阻尼以减小结构地震响应。
The links and viscous dampers increase the stiffness and damping ratio to cut down the seis mic response of bridge.
应用推荐