建立了驾驶员最优控制模型，提出了飞行控制系统优化设计目标函数和设计方法。
The pilot's optimal control model is investigated. The optimal design destination function and method of flight controlling system have been proposed.
在动力学分析的基础上，提出了以织机主墙板处的交叉动柔度为优化设计目标函数的方法，并用传递矩阵方法导出了函数形式。
Base on dynamic analysis, put forward a method of optimize design taking the cross dynamic flexibility of main shaft at major frame as objective function, the model is given by transfer matrix.
传统的优化设计仅以最低造价为目标函数，没有考虑结构的受力性能指标。
The traditional optimization design is only based on the minimum cost objective function and does not consider the mechanical analysis target.
本文在介绍举升机构评价参数的基础上，以油压波动系数为目标函数，对自卸车的举升机构进行了优化设计。
An optimum design is carried out with the hydraulic fluctuation factor as object function on the basis of a description of the evaluation parameters of lifting mechanism.
以带长、带宽、中心距作为目标函数，对齿形带结构参数的优化设计进行了探讨。
The optimum design of synchronous belts with structure parameters is explored in this paper, taking the belt length, width and centre distance as objective functions.
本文提出了以功率消耗为目标函数、犁面几何参数的可行范围为约束条件的犁面优化设计方法。
This paper proposes an optimal method for plow bottom moldboard design by taking the power consumption of the objective and the feasible region of the geometric parameters for boundary constraints.
提出一种评价数据链路系统性能的目标函数，设计了数据链路系统的优化设计算法，并给出其优化结果。
The objective function for evaluating the data link system is proposed, and then the system optimization algorithm and optimal results are presented.
无论如何，假如目标物料号已经存在，那么安排函数将会简单的链接设计到这个已经存在的物料。
In any case, if the target Part number already exists, then the Assign function will simply link the Design to this existing Part.
在此基础上，以壳体重量为目标函数对结构进行了优化设计。
The structure is then optimized based on above methods, taking structure weight as objective function.
用户可以通过人机界面的交互功能确定设计变量、约束条件及目标函数三要素，实现了优化模型建立的柔性。
The users can define design variable, constraints condition and objective function by the alternative function of computer interface, by which the optimization module can be set up expediently.
以振动输送机械能量效率为目标函数，探讨单质体惯性式振动输送机械的优化设计方法。
This paper discussed the optimization design of the inertial vibrating conveyer under the best energy efficiency of conveyer as its objective function.
首先以纵梁各部分单层厚度为设计变量，建立了以车架重量为目标函数的优化模型并进行了优化研究，取得了较好的优化效果。
The first optimum model is established with the target function of the frame's weight as well as with the design variables of the beam's single layer thickness.
实践证明，在自动扶梯zc1蜗杆传动模糊优化设计中，选择啮合面积为目标函数是正确的、可行的。
It is proved correct and practical to choose the meshing area as the objective function in the fuzzy optical design of ZC1 worm transmission in escalator.
建立以年总费用为目标函数的逆流喷雾干燥优化设计数学模型。
The optimum design model of countercurrent spray dryer is established with the annual total cost as the objective function.
基于支承法兰盘的结构特征，通过目标函数的建立、设计变量的选取以及约束条件的确定建立了优化设计的有限元模型，并对法兰盘进行了静力分析。
Based on the structural characteristics of bearing flange, the optimization model is established according to the objective function, design variables and constraints, and make a static analysis.
建立了以递纸牙运动特性作为目标函数的优化设计数学模型，探讨了求解方法。
The mathematical model of the optimization design, which takes the motion characteristics of paper-feeding tooth as the objective function, was established, and the solving method was discussed.
并用PC—1500计算机绘出了可行设计域及目标函数的等高线，确定出优化解。
Variation diagrams in domains of feasible design and contour lines of optimization objective functions are drawn by means of PC-1500 computer. Obtaining optimum solution.
并讨论了双公用齿轮机构优化设计的目标函数和约束条件。
Then in this paper the object functions -and restrained conditions for optimum design are discussed.
并以调节器参数最优化设计为例，论述了目标函数构造、初值确定、动态系统仿真分析的过程。
Taking optimization design of adjustor as an example, the process of constructing object function, defining initial value and simulating dynamic system was discussed.
通过人工弹簧模型和虚拟载荷法描述柔性机构设计的目标函数，采用伴随敏度分析法进行了敏度分析。
The objective function was described by artificial spring model and dummy load method and the sensitivity was analyzed by the adjoint sensitivity analysis method.
小外径的电涡流传感器薄线圈的参数优化设计的关键是寻求合理的目标函数的表达式。
The key of the optimization design of a small eddy current sensor coil is to find out the reasonable expression of the optimization destination function.
建立了PC C桩复合地基优化设计的目标控制函数和两个约束条件：沉降控制条件和承载力校核条件。
The governing object function and two boundary condition: settlement and foundation bearing capacity are developed in the optimization design of the PCC pile composite foundation.
对保温设计的目标函数，采用局部求优，逐步迭代的方法，实现了多层保温经济厚度计算机求解。
Based on the objective function, local optimum and iterative method were adopted to get a computer solution on the optimum economical thickness.
以闭环二阶控制器为例，推导了优化设计的目标函数，探讨了约束条件的确定和优化方法的选择。
The deduction of objective function, the decision of restriction and the chosing of optimizing method are specially discussed with the example of second order feedback controller.
本文对离心式及轴流式通风机采用不同的目标函数、设计变量、约束条件和优化方法进行优化设计。
Centrifugal and axil ventilating fans are optimized by using different objective functions, different variables of design, different constraint forced conditions, different methods of optimization.
用优化设计方法进行滚珠丝杠传动的设计，对设计的目标函数及约束条件进行了分析讨论。
An optimization method has been used in the design of teh ball screw drive. The objective function and constraint conditions are discussed.
论述了钻机最优化设计研究中的某些问题，探讨了钻机优化设计中的目标函数、约束条件和求解方法。
In this article, the authors present the research on the object functions, subject conditions and resolve methods in the optimal methods of borer design.
论述了钻机最优化设计研究中的某些问题，探讨了钻机优化设计中的目标函数、约束条件和求解方法。
In this article, the authors present the research on the object functions, subject conditions and resolve methods in the optimal methods of borer design.
应用推荐