使用字段的属性框指明这是一个计算式字段。
Use the field's properties box to specify that it is a computed field.
详细叙述了改进计算式的推导过程及计算方法。
The derivation process of the formulas and calculation method is described in detail.
从而得到门框上最低温度的计算式。
The lowest temperature of the doorframe is calculated theoretically.
提出了可用于生产实际中的简化计算式。
依据这一原理,推导出经济界限计算式。
According to this theory, derived the calculation formula of economical barriers.
提出了一个曲率修正系数的经验计算式。
An empirical formula of curvature correction factor was presented.
推导出了最佳开孔位置和转速的计算式。
Optimum position of sprinkling aperture and formula of rotating speed are derived.
单层衬里管道的管径及衬里厚度优化计算式。
Formula for calculating pipe diameter and lining thickness of pipelines with single lining.
通过对人工缺陷试件的检测,验证了计算式的正确性。
The correctness of the formulas were proved by test on a specimen with artificial defects.
只有在这个范围内,才能使用式(13)的轴向力计算式。
Only in this context, in order to use equation (13) of the axial force calculations.
表达式求值,用户输入需要计算的计算式,程序计算出来。
Expression for the value of user input required calculation calculation formula, the program calculated.
通过动量、能量和质量衡算的方法可以建立其基本的计算式。
The basic calculation will be defined on the basis of dynamic momentum, energy and mass equilibrium accounting.
通过对不同工质和方案的计算,证实了该计算式是较精确的。
The formula has proved to be accurate through practical calculations for different working mediums and parameters.
本文同时还提供了使用直接加热器时汁汽温度变化的计算式。
Meanwhile,. The equations of the variation of vapor temperature are presented when the direct heater is used.
给出了相应的电流和功率计算式,为设计电炉参数提供了依据。
The paper also gives the relective calculating formula of current and power. and affords basis for designing electric furnace parameters.
提出了计算离散傅氏级数的折线逼近法,并导出了其幅值计算式。
This paper presents the fold line approximation method of discrete Fourier Series, and conducts calculation formula of harmonics.
采用影响函数法推导了薄板轧制时变形区内轧辊弹性压扁的计算式。
A calculation method of the flattening in sheet rolling deformation zone, using influence function, was derived.
叙述了微波吸收材料发射率测量原理、测量方法和有关修正计算式。
This paper describes measurement principle, measurement methods and correlative count formula for the launching rate of microwave absorbing materials.
本文对该项试验方法和成果进行了分析研究,并得出抗磨度的计算式。
The results are analyzed in this paper, and the expressions of the abrasion resistance have been obtained.
一旦你得到一个这样的计算式,你对向量场做点积,这和前面这个不一样。
Once you have such a formula, you do the dot product with this vector field, which is not the same as that one.
对于样本均值估计总体均值,给出了基于误差限制的样本容量的计算式。
The calculation formulas of sample size based on the error limitation are given for estimation of population mean.
用该计算式对一台减压塔的加强圈进行了核算,并与原设计进行了对比。
Stiffening rings of one vacuum tower are checked by this formula, and compares it with original design.
作为补充,又开发了一个对比温度为0.8 ~ 1.0的传导因数计算式。
As complementary, a calculation formula with contrast of 0. 8 ~ 1. 0 for conductivity factors was developed.
为计算平面、球面机构与结构自由度提供了更为方便快捷正确的理论计算式。
The easy and correct theoretical calculating formula is provided for calculating degree of freedom of planar and spherical mechanism.
给出高强钢焊趾表面裂纹在压弯组合应力下应力强度因子及其疲劳寿命计算式。
The formulae for calculating SIF and fatigue life of surface crack at weld toe of the high-strength steel under the combination stresses have been presented.
最后建议对于道路照明计算应采用由反应时间法获得的光视效能最大值计算式。
At last, it was proposed that equation derived from reaction time should be used in road lighting calculation.
给出了高强钢焊趾表面裂纹在压弯组合应力下应力强度因子及其疲劳寿命计算式。
The formulae for calculating SIF and fatigue life of surface crack at weld toe of the high-strength steel under the combination stresses were given out.
对环状波形阀簧的变形特性和应力状态进行了理论分析,得到了一系列设计计算式;
This paper analyzes the load-deflection and stress characteristics of the ring-wave spring in theory, and obtaines several calculating formulas.
这个分离效率计算式不仅适用于选矿各作业,同样也适用于有分离过程的其他行业。
This formula not only applies to ore dressing operation, but also applies to separating operation of the other professions.
这个分离效率计算式不仅适用于选矿各作业,同样也适用于有分离过程的其他行业。
This formula not only applies to ore dressing operation, but also applies to separating operation of the other professions.
应用推荐