要不时地搅拌牛奶蛋糊,防止其表面结皮。
以减压渣油为燃料的常减压加热炉在长期生产运行过程中,对流室钉头炉管表面结垢严重。
In the long-term operation of atmospheric and vacuum heat furnace that use vacuum heavy oil as fuel, thesurface of nailhead furnace tube in the convection chamber was seriously deposited.
烟气中的飞灰既在液相膜表面结壳,阻碍石灰石的溶解,又影响脱硫系统含尘量排放指标,降低石膏品质。
Fly ash in flue gas not only crusts on the surface, stopping the dissolving of limestone, but also affects the dust discharge index, reducing the quality of gypsum.
加热器管表面功率负荷低,介质不会在表面结垢、粘结、烧焦、碳化等,是粘性、热敏性液体介质加热的理想元件。
Low power rate on the surface of heating tube. Medium does not scale, congeal, sinter or carbonize on the surface, and so is ideal heating element for viscous, and heat sensitive liquid medium.
结果表明,复合系统的舒适性最好,而且其冷板表面结露的危险也比顶板辐射供冷单独运行时小,可适用的冷负荷范围广。
Results show that the thermal comfort of combined system is the best, and the risk of condensation is lower than that when chilled ceiling panel operates individually.
据此提出了考虑垢层表面温度变化的描述结垢过程的传热传质模型。
A heat mass transfer model is constructed to take the variation of the scaling layer surface temperature into consideration.
从准异质结的概念出发,讨论了表面费米能级钉扎现象。
Finally, according to the concept of quasi-heterojunction the Fermi energy level pinning on the surface is discussed.
本文在建筑物外墙内表面温度大于室内空气露点温度的条件下,对结露问题做了实质性的讨论。
The dew condensation problems have been substantially discussed under the condition that the inside surface temperature of exterior wall is higher than that of the indoor dewpoint.
观察了在热应力作用下gjw35钢结硬质合金表面热疲劳裂纹扩展过程。
The process of thermal fatigue crack propagation on the surface of steel bonded carbide GJW35 under the action of thermal stress has been observed.
用能量法求解了绑结层合板和编织层合板等3d复合材料中纤维搭桥的椭圆形表面脱层屈曲问题。
By using energy method, the problem is discussed of the delamination buckling of a fiber bridge elliptical surface made of stitched laminates and woven laminates with 3d composites materials.
其表现为:1、熔结环氧粉末(FBE)层偏薄,不能完全覆盖管道金属表面。
The non-conformities are as follows: 1, the thickness of FBElayer is thin, the FBE coating material can not cover the steel surface entirely.
在过冷流动沸腾条件下,对硫酸钙的沉积过程进行了研究,考查了不同流速和不同加热器表面条件下硫酸钙的结垢状况。
The formation process of calcium sulphate deposition during subcooled flow boiling heat transfer was reported. Fouling runs were carried out at different flow velocities and heat transfer surfaces.
文摘:观察了在热应力作用下gjw35钢结硬质合金表面热疲劳裂纹扩展过程。
Abstract: the process of thermal fatigue crack propagation on the surface of steel bonded carbide GJW35 under the action of thermal stress has been observed.
本文在建筑物外墙内表面温度大于室内空气露点温度的条件下,对结露问题做了实质性的讨论。
This paper has substantially discussed on the dew condensation problem on condition that the inside surface temperature of exterior walls is larger than the indoor dewpoint temperature.
国外会尝试用覆膜滤袋和对滤材表面进行防水处理解决防结露和布袋糊袋的难题,取得了明显的效果。
Abroad will try to use plastic film and bags on the filter surface water solution to deal with anti-condensation and paste bag bag of problems, and achieved significant results.
分析了换热设备结垢的主要影响因素:流体性质、流体流速、材质及表面状况、温度和沸腾等。
Effects of the liquid property, flow rate, material and surface characteristic, temperature and boiling on the fouling of heat transfer equipment are analyzed.
用30%甲醛外敷窦房结区表面,造家兔窦房结急性损伤致缓慢型心律失常模型。
Rabbit brady arrhythmia model due to acute sinoatrial node damage was made by overlaying 30% formaldehyde on the surface of sinoatrial node area.
太阳能电池包括基板,该基板具有在其上的光收集表面以及在该基板内的P-N整流结。
The solar cells include a substrate having a light collecting surface thereon and a P-N rectifying junction within the substrate.
结果表明,对恒壁温情况必须考虑垢层表面温度随时间的变化,这一变化是导致结垢过程渐近特性的重要原因之一;
The results show that the variation of the scaling layer surface temperature is one of the major factors that cause the asymptotic tendency of scaling process.
采用液相烧结法将爆炸压实后的WC钢结硬质合金粉末复合在碳钢表面,对不同烧结温度下的界面组织和抗剪强度进行了研究。
WC steel-bonded cemented carbide powders being compacted by explosive compaction were bonded to the surface of carbon steel using liquid phase sintering.
这样可有效地防止在金属表面形成积碳结层,并能逐渐活化原有的积碳颗粒并慢慢去除,从而保护发动机免受伤害。
So can effectively prevent the metal surface to form carbon "layer, and can gradually activated carbon particles and the original slowly removed, in order to protect the engine from harm."
利用原子力显微镜(afm)观察MIM隧道结的表面形貌,发现结表面存在规则有序的自然粗糙度。
With the help of the atom force microscope (AFM), we observed the junction surfaces and found that there exists semisphere-formed roughness in regular arrangement on the surface.
计算结果表明,流速越大,过饱和度越小,结垢过程越易为表面反应所控制。
The calculation results show that the greater the flow velocity, the lower the supersaturation degree, and the easier the scale formation process will be controlled by a surface reaction.
采用液相烧结法将爆炸压实后的钢结硬质合金粉末复合在碳钢表面,成功获得覆层材料。
Steel-bonded cemented carbide powder processed by explosive compaction was successfully bonded to the surface of carbon steel through liquid phase sintering.
采用液相烧结技术成功地将爆炸压制后的钢结硬质合金混合粉末(对应国家牌号TLMW50)复合在碳素钢的表面。
Steel-bonded cemented carbide powder mixture(TLMW50) processed by explosive compaction was successfully bonded to the surface of carbon steel through liquid phase sintering.
采用液相烧结技术成功地将爆炸压制后的钢结硬质合金粉末复合在碳素钢的表面。
Steel-bonded cemented carbide powders being compacted by explosive compaction were bonded to the surface of carbon steel using liquid phase sintering.
强化传热表面在工业换热设备中具有广泛应用,其表面状况对于传热与结垢过程均有重要影响。
Enhanced surface was used in heat transfer equipment widely, and the surface condition has an important influence on the fouling process.
给出表面电场强度、主结及环结分担电压的解析表达式。
The analytical expressions about surface electric field intensity and voltage undertaken by main junction and ring junction are presented.
给出表面电场强度、主结及环结分担电压的解析表达式。
The analytical expressions about surface electric field intensity and voltage undertaken by main junction and ring junction are presented.
应用推荐