涂料中胶粘剂的用量直接影响纸张的印刷表面强度、白度、不透明度、光泽度和吸收性。
The surface strength, brightness, opacity, glossiness, and absorbency are influenced by the amount of binder in the coating.
但成纸的施胶度、抗张强度及表面强度受到影响。
However, the sizing degree, tensile strength and surface strength were damaged to some extent.
氧化淀粉用作纸张的表面施胶剂可提高纸的表面强度。
Oxidized starch used in surface sizing can increase the surface strength of paper.
采用液体喷丸方法提高零件表面强度及抗应力腐蚀能力。
Wet spraying pellet was used to improve the surface' s strength and stress corrosion resistance of the workpiece.
浆内添加时有较好的增强、助留效果，用于表面施胶可明显提高纸张表面强度。
CMS has significant effect on strength and retention when it is used in the pulp; paper surface strength can be improved greatly when it is used as surface treatment size.
该模具具有成本较低、开发周期短、精度较高等优点，但表面强度和热效率较低。
The mould had merits such as low cost, short development cycle and high precision, while it had defects of low surface strength and thermal efficiency.
该产品在涂布纸的面涂涂料中应用，能明显增强涂布纸的表面强度，提高纸张涂布光泽度。
The product is applied in coating paper surface paint, can obviously strengthen the surface strength of the coating surface and improves paper coating glossiness.
对部分混凝土工程实例中表面强度偏低的原因进行分析，论述了粉煤灰对混凝土表面强度的影响。
This article analyzes the causes of the lower surface strength in some practical concrete projects, discusses the influence of fly ash on the concrete surface strength.
为了提高铝合金的表面强度，根据铜合金的液相分离性质，采用CO2激光熔覆方法在铝合金表面成功制备了铜基合金涂层。
According to the liquid separation property of Cu-base alloy, the Cu-base coating is obtained on the aluminum alloy by CO2 laser cladding for improving the surface strength of aluminum alloy.
当表面与射线垂直时，射线的强度最大。
When a surface is perpendicular to the rays, their intensity is at its maximum.
其表面的多角形组成部分对紫外光产生反应，映射太阳光线的方位和强度。
The polygonal segments of the surface react to ultra-violet light, mapping the position and intensity of solar rays.
这些盖由钢制成，以便具有足够的强度，并在密封表面装配有弹性部件。
These covers are constructed of steel for strength and fitted with elastomer components on the sealing surfaces.
介质阻挡放电(DBD)处理聚合物表面可有效提高其亲水性和结合强度。
Dielectric barrier discharge (DBD) can be applied to modify polymer surface to improve its wettability and adhesive strength.
并通过实际应用，证实了激光表面强化处理具有使硬质合金制品的抗弯强度、耐磨性能大为提高的显著效果。
Practice shows that the laser treatment of hard metals surface can significantly increase the product's bending strength and wear resistance.
它具有滚压刚化表面，不仅断裂模数大、耐压强度高，而且具备良好的抗磨损和抗热气腐蚀能力。
It has a rolled, rigidized surface which gives it a high modulus of rupture and compressive strength as well as high abrasion and hot gas erosion resistance.
本文从实验装置、工艺流程、接合机理、接合强度以及影响因素等方面综合评述了表面活化常温接合技术研究的进展状况。
A review on the development including the equipment, technique, mechanism, bonding strength and the related factors of surface activated bonding at room temperature is given in this paper.
同步碎石封层具有强度高、表面粗糙、防滑、不透水、耐久性好、防止雨天行车水雾等优点。
Synchronous chip seal layer has many advantages, such as high strength, surface, non-slip, waterproof, durability, preventing driving rain and so on.
经过退火及冷加工的热轧不锈钢棒材，其表面质量更高，强度也更高。
Hot rolled stainless steel bars that are annealed and cold worked to produce a higher surface quality and higher strength.
给出表面电场强度、主结及环结分担电压的解析表达式。
The analytical expressions about surface electric field intensity and voltage undertaken by main junction and ring junction are presented.
当表面与射线垂直时，射线的强度最大。
When a surface is perpendicular to the rays, their intensity is at their maximum.
你可以降低灯光强度，但物体表面仍然会偏亮。
You can decrease the intensity, but the surfaces will always be lighted a tad bit.
乙基化的选择性则与催化剂的表面酸强度、酸性中心位置和孔道结构等因素有关。
Ethylation selectivity, was affected by strength of surface acid sites, location of acid sites and pore structure.
通常用X射线衍射线的半高宽作为材料表面的强度指标。
In general, the half width of X-ray diffraction is used as a strength index of material surface.
结果表明，散射强度与表面纹理结构、涂层材料的光学性质有关。
The results indicate that scatter intensity is dependent on surface veins and optical properties of coatings.
采用线弹簧模型求解多个共面任意分布表面裂纹的应力强度因子。
The stress intensity factors of multitudinous arbitrarily distributed coplanar surface cracks are solved by using the line - spring model.
研究了预塑变对爆轰处理和未爆轰处理样品的强度、表面残留应力、氢脆敏感性及其关系的影响。
Investigation was made of effect of preplastic deformation for unexplosive and explosive treatments on strength, surface residual stress and hydrogen embrittlement of the specimens.
结果表明：随着纤维素酶和半纤维素酶用量的增加，杨木的表面自由能和胶合强度逐渐上升。
The results show that the surface free energy and gluing strength of poplar increase with the dose of cellulase and hemicellulase rising.
陶瓷轴承球的表面缺陷会严重降低球的强度和滚动接触疲劳寿命。
Surface defects in ceramic bearing balls may significantly affect ball strength and reduce rolling contact fatigue lifetime.
陶瓷轴承球的表面缺陷会严重降低球的强度和滚动接触疲劳寿命。
Surface defects in ceramic bearing balls may significantly affect ball strength and reduce rolling contact fatigue lifetime.
应用推荐