扭力胶芯，发动机减震器垫，减震器。
更换万能防喷器胶芯。
其结构由壳体、全封总成、悬挂器总成、自封胶芯总成四部分构成。
The structure consists of four parts : shell, whole seal assembly, hanger assembly, self seal rubber core assembly.
井压较低时，关闭环型防喷器，使油管和接箍强行通过环型防喷器胶芯。
Close the annular blowout preventer as the well pressure is relatively low and force oil pipes and couplings to pass through rubber core of the annular blowout preventer.
研制旋转防喷器有几大难点，主要集中在密封胶芯、旋转动密封及轴承，各自的寿命满足实际应用是保证钻井施工安全的关键。
There are many difficulties during the new rotating blowout preventer's manufacture and test, they concentrate on spherical seal, dynamic seal and bearings.
利用麻杆制浆废液和废弃麻芯代替部分脲醛胶及刨花压制刨花板的研究。
The substitution of UF resin in making flakeboard with bluish dogbane pulping waste liquid and bluish dogbane pith was studied.
可编程控制器（电脑）控制生产程序。喷胶、封口、切纸、换芯自动同步进行。
Production Procedure is controlled by Programmable controller system. Spraying, sealing, cutting and core exchanging are conducted synchronously.
包封面：在书芯(用铁丝平订，胶装或线装造成)的脊部加胶，贴上纸或纸板书皮的情况。
Wrappering: Attaching a paper or board cover by gluing at the spine of a book block which may be stabbed, adhesive bound or sewn.
应用试验结果表明，J- 164胶是一种理想的蜂芯拼接用胶黏剂。
The results of application experiment indicated that J-164 was a desirable room temperature curing core splice adhesive.
研究了施胶板坯的含水率对刨花板热压过程中表、芯层温度的影响。
The effect of mat moisture content on the surface and central layer temperature was investigated.
研究了凯赛微珠在钢丝绳芯输送带粘合胶中的应用。
Applications of Kaisai micro bead in adhesive rubber of the steel cord conveyor belt were introduced in this paper.
介绍采用多芯胶管的液压支架控制系统及其使用的多芯胶管的结构特点。
This paper introduces a control system for hydraulic powered supports by using multiple-core pipes, and puts a structure-characteristic of the multiple-core pipe.
磁芯经过二次退火后，由于封装胶发生膨胀使得被封装的磁芯电感值严重下降，软磁性能下降。
After cores being secondary annealed, expansion of packaging glue happen, which causes that the inductance value of magnetic-cores declined seriously, soft magnetic properties reduced.
经过研究发现，以明胶-阿拉伯胶为壁材得到的微胶囊，囊壁光滑、透明性好，对芯材包封率高，达到91.2%。
It was found that microcapsules with gelatin-gum Arabic as wall material had smooth surface, superior transparence and encapsulation efficiency high to 91.2%.
本文通过金属套管和改性聚醚醚酮复合材料棒芯的胶接实验，证明了在缸体的加工中使用胶接工艺是不合适的。
After the experiment of gluing stainless steel and modified PEEK composites, we knew the cylinder couldn't be manufactured by gluing.
产品试验结果表明，阀芯在批次和典型试验后掉胶、脱胶问题已基本得到解决，直接模压成型工艺可以生产出满足要求的充气阀阀芯。
Product testing results proved that the problem had been solved successfully. The charge valve cores produced through the direct molding technics can satisfy all requirements.
换纸芯、喷胶、切纸自动顺序在机进行。
Paper core replacement, glue spraying and paper cutting undergo automatically according to given sequence.
并介绍了覆盖胶、芯胶和成品带的物理机械性能。生产出的输送带产品性能较好。
And introduced the physics mechanics performance of the covered compound, core compound and finished conveyor belt.
本发明由外筒、胶塞、芯杆和推杆组成。
The invention consists of an outer tube, a rubber stopper, a core bar and a push bar.
它是采用复凝聚法，以稀禾定为芯材、以明胶和阿拉伯胶为壁材的缓释型微胶囊水悬剂。
The slow-release microcapsule water suspension agent uses the sethoxydim as core material by complex coacervation method and uses the gelatin and the arabic gum as wall material.
它是采用复凝聚法，以稀禾定为芯材、以明胶和阿拉伯胶为壁材的缓释型微胶囊水悬剂。
The slow-release microcapsule water suspension agent uses the sethoxydim as core material by complex coacervation method and uses the gelatin and the arabic gum as wall material.
应用推荐