将数字管脚初始化为输出信号。
制止使用龙门架、钢管脚手架架起电线线路。
How to stop the use of Longmen set up the electrical wiring frame, steel pipe scaffold.
模拟管脚电压读数紧密取决于Arduino的供电电压。
Analog pin voltage readings seem to depend critically on the voltage of the power supply to the Arduino.
通过CAD实验对FPGA的逻辑块管脚分布进行了研究。
This paper investigates the distribution of FPGA logic block pins by CAD experiments.
施加的压力作用在一个膜片上，于是该膜片就移动阳极管脚。
The applied pressure acts on a diaphragm which in turn moves the anode pin.
这样即把安培表连接到了管脚1，将电压源连接到了管脚2和3。
This will connect the ammeter to pin 1 and the voltage source to pins 2 and 3.
闭锁可以保持8个比特的信息，这8个比特在输出管脚得以显示。
The latch can hold 8 bits of information, and these 8 bits are represented on the output pins.
网架安装采用空中散拼的施工方法，采用钢管脚手架临时支撑体系。
The construction method of air assembling separately for grid installation is adopted, the same as temporary support system of steel scaffold.
本文同时也对扣件式钢管脚手架极限承载力的进一步研究进行了展望。
This paper also makes the prospect of further research on the ultimate bearing capacity of steel tubular scaffold.
尽管脚本的详细信息不在本文的讨论范围内，但我在下面给出了一个示例。
Although the details of scripting is beyond the scope of this article, an example is below.
SP505还包括一个带有驱动器和接收器地址译码器的锁存使能管脚。
The SP505 also includes a latch enable pin with the driver and receiver address decoder.
根据市场需求，定义了芯片的规格，管脚功能，设定了芯片的性能指标。
According with the requirements of market, the spec, the pin's function and the performance of this chip have been defined.
在本例中，所提供的数据是该请求瞬间在模拟管脚3、4、5和6上所经历的电压值。
In this case, the data provided is the voltage experienced at the instant of the request on analog pins 3, 4, 5, and 6.
即便是最坚定的管头管脚的人也知道，她收取报酬是来专心处理大事情的。
Even the most determined micromanager knows she's being paid to focus on the big picture.
上述代码给出了管脚的编号以及0至1023范围内的数值，两个数字之间以冒号分隔。
This gives the number of the pin and the value from a scale of 0 to 1023, the two Numbers separated by a colon.
二是提供READY信号管脚，由外部电路控制可以产生任意数目的等待周期。
Another is to provide the READY signal pin, it can produce arbitrarily number of wait period with the exterior control circuit.
我触碰了错误的管脚，从而导致了电流的反转，结果那块电路板上的所有二极管都被烧坏了。
I touched the wrong pins causing a current reversal and all of the diodes on the circuit board exploded.
对芯片管脚的测试可以提供100%的故障覆盖率，且能实现高精度的故障定位。
For testing chip pins, the fault coverage can reach 100%, and the fault position can be positioned with high accuracy.
因此，高层建筑结构施工中，分段悬挑搭设的扣件式钢管脚手架应用得非常普遍。
Therefore, high building structure construction, segmentation cantilever of the fastener type steel tube scaffold built very common application.
在该图中，我们测量一个多管脚的连接器中某个管脚与其它所有管脚之间的绝缘电阻。
This diagram shows measuring the insulation resistance between any one pin and all other pins on a multipin connector.
本文主要介绍扣件式钢管脚手架和碗扣式钢管脚手架在桥梁施工中的一些实际应用。
This paper introduces the actual application of two kinds of steel - tube scaffolds to bridge construction, i. e. clip - holding steel - tube scaffold and bowl - holding steel - tube scaffold.
为了响应此请求，它发送一个标准的http响应头、从相关管脚收集读数并以文本格式发送数据包。
In response to a request, it sends a standard HTTP response header, collects readings from the relevant pins, and sends the data package in text format.
UT9Q512E和UT9Q513K32分别采用的是36和68个管脚的封装，但尺寸略有不同。
The UT9Q512E and the UT9Q513K32 are available in 36- and 68-pin packages, but with slightly different dimensions.
微处理器管脚用下拉电阻R1与地相连，阻抗典型为几百千欧，在管脚上呈现出高阻状态。
The microcontroller's pin connects to ground using pulldown resistor R1 with resistance, typically, of a few hundred kilohms to impress the high-impedance state on the pin.
文中介绍了TDA5051A的内部组成、管脚功能及工作原理，并给出了其典型应用电路。
The internal structure, pin function and operation principle of TDA5051A are introduced, the typical circuit is also given.
在本论文中应用逻辑编程对GAL进行设计，管脚可灵活定义，使电路结构紧凑，连线简单。
I use logical program to design GAL in this dissertation, the pin can defined agility, this made the structure of circuit compactly and connect simply.
本文对扣件式钢管脚手架杆件接头型式问题，从承载能力，受荷变形方面进行了试验和分析。
This article discusses the joint-types of buckle-type steel tubular scaffold, and analyzes the experiments with load-bearing capacity and load deformation.
以管脚编号为中心，然后再进入到一个switch结构，根据连接到此管脚的传感器来采取不同的措施。
Focusing on the pin number, it then goes into a switch structure that takes a different action depending on which sensor is connected to the pin.
本文应用机器视觉和机械自动化技术，研制自动检测设备，实现集成电路芯片管脚尺寸检测自动化。
In this paper, we develop an automated inspection device by computer vision and mechanical automatization technology, to realize the automated inspection on integrated circuit chip pin size.
济南遮阳蓬施工现场内的龙门架、井字架等巨大设备及钢管脚手架，若没有防雷设备应设备防雷设备。
Longmen, frame, derrick and huge equipment and steel scaffolding Ji 'nan awning in the construction site, if there is no lightning protection equipment equipment lightning protection equipment.
应用推荐