所以，只要稍微花费一点时间进行适当的保养，就能够很好地控制其磨损度。
Therefore, as long as a little bit of time spent to carry out proper maintenance, they can better control its degree of wear and tear.
通过对反射式光纤位移法检测原理的理论分析，给出了轧辊磨损度测量的理论依据。
Through analyzing the principle of the reflective fiber-optic displacement method theoretically, the base of detecting roller wear is presented.
根据轧辊磨损度测量过程的特点及精度要求，对传感器电路系统的原理、组成及性能进行了分析。
According to the characteristic and the measuring accuracy of roller wear testing course, its principle, construction, and function of the sensor circuit are analysed.
基于反射光强与位移在一定范围内成正比的原理，提出了用反射式光纤传感器对轧辊磨损度进行非接触式在线检测的方法。
Based on the principle that reflected light intensity is proportion to the distance in some extent, a non-touch on-line optical fiber measurement for roller wears is presented.
实验室检测显示，这种瓷粉会与唾液反应在瓷层表面形成一个硅羟基层，这个硅羟基层更软，磨损度更小，与传统瓷粉相比对对颌牙更温和。
Laboratory tests reveal it reacts with saliva to form a silica-hydroxyl layer on the ceramic that is softer, less abrasive, and gentler to opposing dentition than conventional porcelains.
齿轮在齿厚部位都是单侧磨损，所以可将齿轮翻转180度使用。
Gear tooth thickness at the site are unilateral wear, so gear can be rotated 180 degrees to use.
随着道路试验里程的增加，由于微动磨损的不断加剧，其销轴与外链板孔、套筒与内链板孔的联结牢固度在逐渐降低。
With the increasing of road test mileage, because of the fretting wear picking up, the combined firm degree of pins and outer link plate bore, bushings and inner link plate bore is declined gradually.
本文介绍模拟试验中轴承表面光洁度和配合间隙与磨损的关系，同时简述了磨损试验和测量方法。
This paper investigates the influence of bearing's surface finish and clearance on its wearability obtained by simulating tests. The method of the wear test and measurement are briefly described.
这样会使得材质易于操作、增强颜色对比度、防止磨损、消除会聚集在所有小洞里的水和污物。
It makes the material easier to work with, enhances the colors, protects against abrasion and eliminates the build-up of water and dirt that will collect in all the small holes.
同时对环氧腻子层的磨损小，提高环氧地面的平整度。
Since there is less wear on epoxy putty layer, it can promote the flatness of epoxy ground.
化学气相沉积的碳化物镀层一般很耐磨，但这些表面层镀后的粗糙度较高，会使与之相配的试件受到剧烈磨损。
In general, the carbide coating of chemical vapour deposition resists wear. But these surface coatings have a high roughness, which causes violent wear in the matched test pieces.
为了精确测量气缸套磨损分布，需要使用高准确度测量系统。
In order to accurately measure the wear distribution law of cylinder liner, the application of high precision measurement system is necessary.
铣削加工表面粗糙度的形成与铣刀和工件振动、主轴偏心、刀具磨损、刀具变形等物理和几何因素有关。
The surface roughness in mill machining relates to quiver of work piece, principal axis's eccentricity, cutter abrasion, cutter distortion and other physical or geometry factors.
同时，还研究了煤粉细度与炉膛出口烟温、飞灰磨损的关系，得出了一些有意义的结论。
Meanwhile, the relations between finenesses of coal_dust, temperatures of flue gas at boiler exit and fly ash erosion are studied.
用三坐标表面粗糙度仪测量了磨损体积，利用脉冲电位评价磨损产生的新生面与磨损表面的关系。
The wear volume was measured with 3D measuring instruments and the relationship between the fresh surface that fretting wear produces and worn surface was evaluated with the potential pulse method.
本文叙述了在线表面粗糙度检测技术在动态微磨损研究中的应用。
The application of on-line surface roughness measurement technique on dynamic micro-wear study is introduced in this paper.
通过玻璃纤维增强塑料的车削试验，研究了薄膜与基体之间的附着强度、涂层刀具的磨损和加工工件的表面粗糙度。
The adhesive strength of the films to the substrates, diamond-coated tool wear and surface roughness of the workpiece were further studied by turning glass fiber reinforced plastic cylindrical bars.
表面粗糙度有一个最佳值，在这个表面粗糙度下电弧能量最小、质量磨损率也最小。
There is an optimum surface roughness which will produce minimal arc energy and minimal wear rate.
工作辊磨损后，粗糙度递减导致在较高轧制速度下进料(咬入带卷)时产生滑移。
When work rolls become worn the roughness is diminishing creating slippage in the roll bite at higher speeds.
研究表明增加砂轮线速度可以降低磨削力、工件的表面粗糙度和砂轮的磨损，或者可以提高生产效率。
It has been proved that increasing the speed of the grinding wheel can lead to a reduction in grinding forces, grinding wheel wear, and in workpiece surface roughness, or an increase in productivity.
耐高温，抗磨损性好，增强了清理效果，适用于清洁度要求较高的部位。
With high temperature resistance, excellent wear resistance and strengthened cleaning performance, it is applicable to the sections that are highly demanding on cleaning effect.
探讨橡胶接触轮硬度、每次进给的磨削深度、磨削力和砂带磨损对工件表面粗糙度的影响。
The hardness of the rubber contact wheel, the grinding depth of the workpiece per feed once.
提高主轴的加工精度和降低表面粗糙度，可提高主轴的旋转精度和减少主轴的磨损。
High machining precision and low surface roughness may improve the main spindle rotating precision and decrease the wear of the main spindle.
路面平整度，不但直接关系到行车的安全、舒适，还会影响车辆的燃料消耗、轮胎磨损、运输时效及其它经济指标。
Pavement, not only directly related to traffic safety, comfort, but also affects vehicle fuel consumption and tire wear, Transport aging and other economic indicators.
路面平整度，不但直接关系到行车的安全、舒适，还会影响车辆的燃料消耗、轮胎磨损、运输时效及其它经济指标。
Pavement, not only directly related to traffic safety, comfort, but also affects vehicle fuel consumption and tire wear, Transport aging and other economic indicators.
应用推荐