玻纤复丝经编针织物的用途。
并简叙了玻纤增强塑料熔合缝的结构和性能。
Indicate the properties and structure of knit-lines for fiber reinforced plastics.
研究了玻纤用量对复合材料力学性能的影响。
The effect of the fiber content on the mechanical properties of the composites was studied.
玻纤复丝在舌针经编机上加工时的其它一些问题。
Other problems arisen in knitting glass filament on Raschel latch-needle warp knitting machine.
以生产规模衡量，该公司是中国第二大、世界第四大玻纤生产商。
It is the second-largest fibreglass producer in China and the fourth-largest in the world in terms of production scale.
利用空心微珠球型的特性，填充改性玻纤增强尼龙6。
The glass fiber reinforced nylon 6 was modificated by the filling of the hollow microsphere.
采用熔体浸渍工艺制备长玻纤增强PA 6复合材料。
Composite was prepared with melt dipping that PA6 enhanced with the long glass fibre.
本文还对玻纤增韧，增强聚氯乙烯的机理进行初步探索。
Mechanism of glass fiber toughened and reinforced PVC is also discussed.
本文介绍了玻纤拉丝温度数字控制系统的一种控制算法。
Control algorithm of the temperature digital control system for glass-fibre wiredrawing is introduced in this paper.
采用悬浮浸渍拉挤成型法制备长玻纤增强ABS复合材料。
Long glass fiber (LGF) reinforced ABS composite was prepared by means of a new method.
我司可供应两种不同类型的嵌缝带，即自粘网格带和玻纤薄毡带。
We offer two kinds of fiberglass joint tapes, sell-adhesive mesh tape and glass tissue tape.
得出了不同含量玻纤增强PP挤出吹塑制件的最小壁厚的参考值。
The minimum reference value of the wall thickness of GF/PP products with different content of GF was obtained.
介绍了无砷澄清剂在中碱玻纤配合料中的加入量及相关原料的调整。
The use of arsenic-free refining agent in C-glass batch and the corresponding adjustment of relative raw materials are introduced.
试验结果表明：玻纤增强复合土工布具有强度高、抗蠕变能力强的优点。
The experimental results show that the glass fibre reinforced composite geotextiles possess excellent tensile strength and creep deformation resistance.
GMT材料流动成型后玻纤在平面内发生取向，导致模压件呈各向异性。
The planar orientation of fibers may occur after the flow molding of GMT, which can result in anisotropy molded parts.
研究结果表明，复合材料的冲击强度、拉伸强度随玻纤用量的增加而提高。
The result showed the impact strength and tensile strength of the composite increased with the increase of the content of the glass fiber.
建筑外表面覆盖了模塑玻纤板，采用石膏和灰泥饰面以实现光滑度和延伸感。
The buildings exterior surface is covered in molded fiberglass panels with a plaster stucco finish to achieve the smooth and stretched quality.
该成膜剂有效提高玻纤的浸润性、硬挺性，以适应FRP新工艺对玻纤的要求。
It increased effectively the impregnation, stiffness of glass fiber, so as to meet the requirements of new technique of FRP.
从玻纤生产各工序出发，并以浸润剂技术为重点，分析了玻纤毛丝产生的原因。
The causes of fuzz formation in each step of glass fiber production were analyzed, with sizing technology as a focal point.
全面分析复合玻纤板风管，介绍其主要技术性能指标，并简单叙述其制作和安装。
Analyses glass-fiber board air duct, introduces its main technical characters, and briefly narrates its fabrication and installation.
断面形貌的变化与玻纤在基体树脂中的应力集中作用及对裂纹扩展的阻碍作用有关。
Change of section appearance is related to stress concentration of glass fiber on the base resin and on hindering of crack extension.
导纱材料在玻璃纤维生产过程中普遍使用，选择合适的导纱材料对玻纤生产非常重要。
Glass fiber guides are commonly used in glass fiber production, so the selection of guide materials is very important.
玻纤格栅是一种提高沥青混凝土路面性能的新材料，对沥青混合料起到物理改性作用。
Glassgrid is a new material that can improve the property of asphalt concrete pavement. It can also change the physical characteristic of asphalt mixture.
制备了结晶速率快、力学性能优异的玻纤增强聚对苯二甲酸乙二酯（PET/GF）。
A kind of PET/GF composite with good mechanical properties and rapid crystallization rate was prepared.
抗裂防水保护层材料由抗裂水泥砂浆复合玻纤网组成，可长期有效控制防护层裂缝的产生。
Crack waterproof layer materials by crack cement mortar complex fiberglass nets composition, but the long-term effective control protection layer the creation of cracks.
实验结果表明，将接枝、增强、增韧技术共用，可以获得高性能玻纤增强聚丙烯工程塑料。
The experimental results showed that using the methods of grafting, reinforcing, toughening together could produce high performance GRFPP.
研究了几种硅烷偶联剂、酞酸酯偶联剂对玻纤增强PF尼龙界面粘结状态和力学性能的影响。
The effect of silane and titanate coupling agents on the interface bonding state and the mechanical properties of GRPFN (Glass Fiber Reinforced PF Nylon)has been studied.
依据降低翘曲的机理，选用不同降低翘曲的方法，制备了系列低翘曲玻纤增强PET复合材料。
Series of glass fiber reinforced PET with low warpage have been prepared according to the mechanism and different methods of reduction of warpage.
依据降低翘曲的机理，选用不同降低翘曲的方法，制备了系列低翘曲玻纤增强PET复合材料。
Series of glass fiber reinforced PET with low warpage have been prepared according to the mechanism and different methods of reduction of warpage.
应用推荐