讨论了激光熔区的凝固特征及成分与激光熔区的平均显微硬度的关系。
The solidification phenomena of the laser melted zone and the relationship between the composition and average microhardness of the laser melted zone were discussed.
本文研究了奥氏体不锈钢/普通低合金钢爆焊复合钢板界面熔区的形成。
The paper deals with the formation of melting zone in the interface of explosive cladding austenitic stainless steel/normal low alloy steel system .
结果表明:ZM5合金TIG焊接接头是由热影响区、部分重熔区和焊缝组成。
The results show that the TIG weld joint of ZM5 magnesium alloy is composed of heat affected zone, partially melted zone and weld metal.
对重熔区显微组织进行了研究,研究表明:激光重熔区分为熔凝区、过渡区及热影响区;
The result of microstructures analysis show: there are melted zone , transient zone and heat affected zone in the laser melted layer.
考察了熔区移动速度、区熔次数、熔区长度以及黄磷原料杂质初始含量对提纯效果的影响。
The influence of variable zone lengths, zone passes, moving speed and the impurity of raw materials on the purification process was studied.
结果表明:在焊缝区域内存在着局部未熔区以及铸造疏松组织和二次裂纹等缺陷,这是导致试样低应力断裂的根本原因。
The results show that the partial unmelted region, casting defect structure and secondary crack form in the welding seam, which result in the low stress breakage of the samples.
表面熔凝区的硬度较基体提高了20%。
The hardness of surface remelting zone increases by 20% compared with the substrate.
本文用晶体区熔生长理论对激光加热基座法生长的单晶光纤形状稳定问题作了研究。
In the paper, the shape stability of single crystal fibers grown by laser heating float zone growth method is studied with zone melt growth theory.
研究了区熔再结晶(ZMR)设备及其工艺特点。
ZMR (zone melting recrystallization) apparatus is introduced, and the processing characteristic of ZMR is studied.
得到了点掺杂区熔后杂质沿锭长分布的一系列普遍公式。
A series of general formulae of impurity concentration distribution along the ingot after point-doping zone melting has been derived.
本文是在作者提出的原地重熔模式的基础上,进一步讨论东南地洼区中生代陆壳重熔的大地构造过程以及这一过程所产生的部份区域地质现象。
On the hypothesis of remelting in SITU put forward by the author, this paper discusses both the dynamic process of crustal remelting and the geological effects brought about by the process.
数以百万计的欧洲人来到这个工业区,使它成为人所共知的“熔锅”,将来自各国的人融合为美国人。
Into this area of industry came millions of Europeans who made of it what became known as the "melting pot", the fusion of people from many nations into Americans.
本文讨论玻璃熔窑成型区温度控制方法,提出了计算机直接数字控制系统,给出了该系统的硬件和软件。
This paper discusses the method of Glass Furnace Forehearth Zone Temperatures and presents a direct digital computer system and hardware software.
本文叙述了注射成型中加工参数、物料性能及螺杆结构对存料区熔体温度分布的影响。
The influences of processing parameters, material properties and screw design on melt temperature distribution in reservior during injection moulding are described in this paper.
基于对实际点焊接头硬度分布的分析,建立了包括熔核、热影响区和母材的单点点焊搭接接头计算模型。
Based on the hardness analyses of actual spot welded joints, a computational model that consists of nugget, HAZ and base metal is established for the single point spot welded lap joints.
T1处理时不能消除复熔共晶和基体软化,故热影响区的宏观力学性能降低,但降幅不到10 %。
T1 heat treatment couldn't eliminate remelted eutectic microstructure and matrix softening, so that the mechanical properties of the heat effected area is slightly decreased by 10%.
本文应用X射线透射截面形貌技术研究了氢气区熔硅单晶中氢致缺陷与热处理温度的关系。
The relationship between the annealing temperatures and the hydrogen-induced defects in floating zone silicon grown in hydrogen atmosphere has been investigated by X-ray section topography.
杂质掺杂多晶硅层设置于两绝缘区与反熔丝上。
An impurity doped polysilicon layer is defined over the two insulator regions and the anti-fuse.
对在两相区铸造进行半固态制浆所得az91 D镁合金坯料的部分重熔工艺条件及组织演变进行了研究。
The microstructure evolution and partially remelting processing of two-phase-region casting AZ91D magnesium alloy ingots were investigated.
结果表明,熔凝区晶粒得到细化,镁合金表面的性能得到明显提高。
The results indicate that the grains of the melted layer are refined and the properties of the surface of Mg alloy are obviously improved.
激光熔覆区的显微硬度约为基体的10倍。
The microhardness of the cladding zone is 10 times of the substrate.
结果表明,激光熔覆层在微观结构上存在熔覆区、结合区、基体热影响区三个区域。
The results show that microstructure of clad layers comprises three zones as cladding, bonding and heat-affecting zone.
这些碰撞加热这个再生区,其中的液体冷却剂,如熔盐,会把热从反应堆中导出。
These collisions heat the blanket, and a liquid coolant such as molten salt draws that heat out of the reactor.
结果表明,激光处理后试样表面熔凝区的组织主要为胞状枝晶组织,经后续热处理可转变为细小的等轴晶粒组织,并形成了良好的超塑连接条件。
The results show that, after laser surface processing, a melt layer with cellular-dendrite structure is formed, which could transform into very fine-grained structure during the annealing treatment.
通过蚀坑形貌在晶体横截面内观察到了小面生长核心区和熔质尾迹等缺陷,并分析了其成因。
The defects such as facet growth core and wake of melt were observed from etching figures on (101) face, and their causes of formation were analyzed.
数值计算结果表明:T型接头焊趾区经过TIG电弧重熔处理后,虽然能够改善焊趾的形状,但该部位仍呈拉伸残余应力状态。
The results show that after TIG arc remelting treatment, the T-joint weld toe area can improve the shape of the weld toe, however, the area till shows a tensile residual stress state.
热影响区大部分保留了母材的原始组织特征,小部分区域发生了重熔。
Most of the heat affected zone retained original structure characteristics of the base metal, and only a fraction of the zone remelted.
结果表明:储能焊能够实现TC4钛合金薄板的快速凝固焊接,焊接接头由熔核和熔核向母材过渡的熔合区(线)组成。
The results show that the welding of TC4 can be realized by capacitor discharge welding. The joint microstructure consists of nugget zone and semi-melt zone.
熔锥型光纤器件的光学性能由熔锥区的微观结构和形貌决定,而微观结构和形貌又由工艺条件决定。
The optical performance of the fused-taper fiber device is determined by microstructure and morphology of the fused taper region, which are determined by technological conditions.
对熔覆层和熔覆层与基体结合区的形貌和微观组织进行了研究。
The features and microstructure of the cladding layer and interface layer between cladding layer and copper substrate were analyzed.
应用推荐