义齿焊区未见断裂、开焊、变形及腐蚀变色现象。
There was no joint fractures and corrosions and color changes.
扩散焊接的焊区结合情况直接影响结构的力学性能。
The mechanical properties of diffusion welded structures were strongly dependent on the homogeneity of welded interfaces.
通过宏观及微观检测,分析了6061铝合金管及A7003铝合金薄壁管经TIG(氩弧)焊后的焊接区开裂的原因。
After visual inspection and metallographic test, analysis and discuss the welding zone cracking reasons for 6061 and A7003 aluminum alloy thin-walled tube after TIG (argon shielded arc) welding.
中间焊段的收弧区降低先焊焊段残余拉应力的效果要优于起弧区。
Moreover, the effect of the latter welding subsection's quenching arc region on decreasing residual stress of the prior welding subsection is better than the striking arc region.
通过对螺旋埋弧焊管内焊缝成型和焊接过程的分析,指出焊缝裂纹易产生在焊接熔池脆性温度区。
Through analysis on inside weld forming and welding procedure of SSAW pipe, it pointed out weld crack is easy to appear in brittle temperature zone in welding pool.
剖焊样品的金相检验表明,成品的最小热影响区与母体金属完全相同。
Metallurgical tests of cross-sectional weld samples indicate a minimal heat-affected zone that is identical to the parent metal.
焊接方法为脉冲熔化极混合气体保护焊,焊接板的中心裂纹处于焊缝与热影响区之间的熔合区。
The welding method used was a PC-GMAW process with mixture gases shielding. Central crack for the welded plate was located in the fusion zone between welding seam and heat-affected zone.
热影响区的热循环是决定焊后热影响区组织和性能的重要因素。
Thermal cycling is an important factor to determine structure and property of HAZ after welding.
经焊后回火热处理后,主要合金元素沿焊合区的扩散区宽度增大;焊合区钛合金侧硬度值显著提高。
The diffusion zone width of main alloying elements increases and hardness of the friction weld zone near TC4 titanium alloy side improves after post-weld heat treatment.
这也从分形理论的角度证明了在超塑性固相焊接头的形成过程中,焊接面各微区的焊合状态是非均匀性的。
It is proved by fractal theory that the welded state of every micro zone at welded surface is uneven in the formation process of isothermal superplastic solid-state welding joint.
采用焊道错位叠加方法,再现了螺旋管双面埋弧焊制管过程中内、外焊焊接热影响区(HAZ)的焊接热循环。
In this paper the HAZ weld thermal cycles of the welding by both sides submerged arc welded steel pipe were reproduced by the dislocation overlap weld method.
文中给出的算例表明,适当控制通入的电流强度,可以达到有效控制裂尖熔化区尺寸以及形成焊口的目的。
If a current with proper intensity has been switched on, the goal of controlling the melting and welding dimension effectively around the crack tip can be obtained.
本文研究了奥氏体不锈钢/普通低合金钢爆焊复合钢板界面熔区的形成。
The paper deals with the formation of melting zone in the interface of explosive cladding austenitic stainless steel/normal low alloy steel system .
焊接过程中搅拌焊针的结构形状是影响焊缝区塑性软化材料流动方式的主要因素,从而影响焊缝的成型质量。
The structure and dimension of welding pin are the main factors which affects the flow direction of the plastic metal in FSW zone and the quality of the FSW seam.
采用焊接热模拟试验方法研究了2219铝合金双丝焊热影响区的微观结构和力学性能的变化规律。
Microstructure and mechanical properties changing rules of 2219 Al-alloy HAZ (heat-affected zone) with twin wire welding were studied using welding thermal simulation method.
采用焊接热模拟的方法,模拟HAZ粗晶区组织,并在不同回火参数下对试样进行焊后热处理。
By use of the method of welding thermal simulation, the morphology in HAZ was simulated and the post-weld heat treatment under different tempering parameter to the test specimen was carried out.
结果表明,焊后时效处理温度不同,焊接接头各微区显微组织和硬度发生的变化不同。
The results show that different post-weld aging temperatures lead to variations in microstructure and micro-hardness across the weld.
深圳市福英达工业技术有限公司是一家专业生产合金焊粉的高技术企业,位于深圳市蛇口工业区。
Shenzhen Fitech Co. , Ltd. is located in Shekou Industrial Zone, Shenzhen City, the PRC and is a high-tech enterprise which specializes in the alloy solder powder production.
结果表明:储能焊能够实现TC4钛合金薄板的快速凝固焊接,焊接接头由熔核和熔核向母材过渡的熔合区(线)组成。
The results show that the welding of TC4 can be realized by capacitor discharge welding. The joint microstructure consists of nugget zone and semi-melt zone.
TIG熔修处理工艺在焊趾区引入了残余拉应力,而超声冲击在焊趾区形成了较大数值的压缩应力。
Residual extend stress is produced at weld toe by TIG dressing, while compressing stress of high values by ultrasonic peening.
通过对铸焊齿轮的材料和结构的分析,利用“加热减应区”法及适当的装配焊接顺序,成功地焊接了异种金属的合金钢齿轮。
Through the analysis of material and construction, the dissimilar steel gear is successfully welded using stress reduction zone by heating and proper assemble and welding sequence.
研究结果表明:在不预热条件下,用KD286焊补钢轨,焊缝组织为柱状奥氏体组织,熔合区和过热区不可避免地产生脆硬的马氏体组织。
The results show that:under the no preheating condition, the microstructure of weld metal is columnar austenitic, and brittle martensite exists in the fusion zone and over-heated zone unavoidably.
利用现代分析测试手段分别研究了TIG焊直接焊接镁铝和镀锡焊接镁铝的焊缝熔合区形貌,并对其进行了元素扩散行为的分析及比较。
Modern analytical methods have been used to investigate the patterns of fusion zone and the diffusion behaviors of elements by tig direct welding and tig with Sn as transition layer welding.
公司拥有九洲松下CM 88c - M高速贴片机、多温区回流焊等设备以及空调房生产车间,是产能和品质保证。
JLG will provide production capacity and quality assurance for our customer by Panasonic CM88C-M Hi-speed mounting and reflow equipment in air conditioned workshop.
焊接接头的硬度分布沿焊缝中心基本对称,焊核区硬度较高,热影响区硬度最低。
The microhardness distribution of the welded joint is along the welding line. The microhardness is higher in nugget zone, and lowest in HAZ.
数值计算结果表明:T型接头焊趾区经过TIG电弧重熔处理后,虽然能够改善焊趾的形状,但该部位仍呈拉伸残余应力状态。
The results show that after TIG arc remelting treatment, the T-joint weld toe area can improve the shape of the weld toe, however, the area till shows a tensile residual stress state.
数值计算结果表明:T型接头焊趾区经过TIG电弧重熔处理后,虽然能够改善焊趾的形状,但该部位仍呈拉伸残余应力状态。
The results show that after TIG arc remelting treatment, the T-joint weld toe area can improve the shape of the weld toe, however, the area till shows a tensile residual stress state.
应用推荐