同时,提出了一种确定淬火钢回火工艺的新方法。
And, a new method of determining the technology of tempering of the hardened steel is also advanced.
产品适用于合金钢、不锈钢、调质淬火钢、有色金属等。
Our products are applicable in alloy steel, stainless steel, hardened steel, non-ferrous metal, etc.
利用等温回火实验,采集了淬火钢在不同条件下回火时的硬度数据。
The hardness data of quenched steel under different conditions were collected utilizing austempering tests.
用于铸铁和有色金属精加工和半精加工,也用于锰钢和淬火钢的加工。
The finishing & semi-finishing of cast iron and nonferrous metals and also for the machining of manganese steel and hardening steel.
建立了描述淬火钢圆形截面硬度分布曲线——U曲线的解析函数表达式。
An analytical function for describing hardness distribution in round section of quenched steel, known as U-curve, has been established.
适于加工淬火钢、工具钢、不锈钢、铸铁、硬质合金及超硬材料磨具的修整。
Suitable for processing chilled steel, tool steel, stainless steel, cast steel, carbide and dressing super hard materials.
适合加工淬火钢,合金钢,高速钢,高碳钢等硬度较硬,抗张强度较大的材料。
It can be adopted for the grinding of the hard and strong bending strength materials such as chilled steel, alloy steel, high-speed and high carbon steel.
PCBN刀具适合各种轴承钢、工具钢、淬火钢以及各种高硬度铸铁、喷涂、硬质合金的粗精加工。
PCBN cutters are used for rough and fine processing various of bearing steel, tool steel, chilled steel, and other many kinds of cast steel and carbide of different hardness.
重点分析了陶瓷刀具在切削淬火钢和镍基高温合金中有关切削力、切削温度、刀具磨损等方面的机理。
The mechanism of cutting force, cutting temperature and tool wear in the machining of quenched steel and nickel based high temperature alloy with ceramic tools are analyzed in the paper.
通过试验,论证了淬火钢中硼向奥氏体晶界的偏聚,是在冷却过程中发生的一种非平衡的晶界偏聚现象。
The test has been demonstrated that the boron segregation at austenite grain boundaries in quenched steel is a non-equilibrium grain boundary segregation phenomena occurred during cooling.
研究结果表明,淬火钢的合金元素含量和硬度对刀具的耐用度均有明显的影响,淬火碳钢的可加工性最好;
The experimental results show that the alloying element content of a hardened steel and its hardness have a remarkable influence on the tool life. The hardened carbon steel has the best machinability.
将氮化碳涂层刀具应用于干切削领域,通过对淬火钢的干式切削试验,研究氮化碳涂层刀具的切削加工性能。
The cutting experiments show that in cutting of quenched steel the tool life of this cutter is longer than that of uncoated cutting tool.
试验研究发现,磨削淬硬的磨削力比值范围与磨削淬火钢的磨削力比值范围相一致,大于磨削普通钢的磨削力比值范围。
The grinding force ratio in grind-hardening consists with the grinding force ratio in grinding quenched steel, and is bigger than the grinding force ratio in grinding unquenched steel.
着重说明了车削淬火钢件时,如何通过合理地选用刀具材料、刀具几何参数及切削用量达到理想的切削效果,并提出车削淬火钢件时应注意的若干问题。
The author gave us the reasonable selection of tool materials, tool parameters and cutting parameters during turning of hardened steel in order to get the ideal cutting result.
结果表明,奥氏体的再结晶发生在钢的正常淬火温度以上的一个温度范围,并在该范围内存在晶粒细化效果最佳的温度区域;
The results showed that the austenite recrystallization occurs in a temperature range biger than thenormal quenching temperature and there is an optimum temperature range for the grain refining.
钢的热处理操作主要有三种,即:淬火、回火和退火。
There are three main operations in the heat treatment of steel: hardening tempering and annealing.
钢的热处理操作主要有三种,即:淬火,回火和退火。
There are three main operations in the heat treatment of steel: hardening, tempering and annealing.
淬火就是把钢件加热到或超过它的临界温度范围,然后使其快速冷却的过程。
Hardening is the process of heating a piece of steel to a temperature within or above its critical range and then cooling it rapidly.
快速淬火硬化的钢是硬而易碎的,不适合大多数场合使用。
Steel that has been hardened by rapid quenching is brittle and not suitable for most uses.
本文介绍国产A508-3钢在不同的淬火、回火和退火条件下的热处理实验的某些结果。
This paper presents some results of heat treatment experiments of A508-3 steel at different quenching, tempering and annealing conditions.
介绍了国内外调质表面淬火齿轮用钢的情况。
This paper reviews the steel grades for the quenching - tempering and surface - hardening gears.
关于钢的淬火和回火有两个要点需要注意。
Two important points are to be noted in connection with the quenching and tempering of steel.
介绍了45钢渗氮淬火复合处理工艺。
In this paper, technology of nitriding quenching of 45 steel is presented.
分析结果表明,在H13钢淬火过程中,操作不当是使加厚模产生裂纹的主要因素。
The results shows that during the quenching process of H13 steel, the improper operation is the main factor to produce the cracks on the thicker mould.
热处理、碳化、淬火硬化层,表面覆层,钢,有色金属,微小及薄形零件等。
Heat treated layer, carbonized layer, hardened hard layers, superficial coating, steels, non-ferrous metal, micro and thin shaped components.
粉末合金刹车片在烧结后有时会意外淬火,造成刹车片钢背脆化而报废。
The accidental quenching, occurring in the sintering process, will make the steel back of a powder alloy brake lining brittle and useless.
研究了搅拌速度和搅拌方式对MH介质冷却特性及钢件淬火质量的影响。
The effect of stirring rate and stirring method on the cooling characteristics of MH quenchant and the quenching quality of steel pieces is investigated in this paper.
本文研究了合理缩短45钢件在箱式炉中淬火加热时间。
This paper investigates the rational decrease of hardening heating time of 45 steel parts in the box furnace.
本文研究了合理缩短45钢件在箱式炉中淬火加热时间。
This paper investigates the rational decrease of hardening heating time of 45 steel parts in the box furnace.
应用推荐