阀座两边的测压点用于流量测量。
Pressure tapping points on either side of the seat provide the means for flow measurement.
单点测压元件是特别为平台称重设计。
Single-point load cells are especially designed to be used in platform weighing.
它是工业上应用最为广泛的一类测压仪表。
They are ones of the most frequently used pressure meters to measure pressures in industrial application.
BE及对照组间在食管测压上无显著性差异。
There was no difference in esophageal motor function between RE, BE groups and controls.
目的探讨肛管直肠测压技术的临床应用和意义。
Objective To evaluate the clinical appliance and significance of the technique of anorectal manometry.
目的观察食管曲张静脉测压数字图像系统的可靠性。
Objective to develop a digital video system for esophageal variceal manometry and to evaluate its reliability.
这款测压元件特别适合于高精度和整体高度低的情况。
These load cells are notable for high accuracy and low overall height.
为提高数值积分精度，测压孔位置按高斯求积节点布置。
The pressure taps are arranged as the nodes of Gauss numerical integration to improve the accuracy of integral.
本文主要对电容式测压微传感器的力学特性和电学特性进行分析。
The mechanics and electrics characteristics of a type of capacitive microsensors are introduced here.
结论：食管测压对诊断原发性与继发性食管运动障碍均有较大价值。
Conclusion: esophageal manometry had great value in the diagnosis of primary and secondary esophageal motility disorders.
结论食管曲张静脉测压数字图像系统能准确地测量食管曲张静脉压力。
Conclusions the esophageal variceal pressure can be measured accurately by the digital video system made by us.
采用测压方法研究了矢量喷流对细长旋成体大迎角非对称流动的影响特性。
This paper studies the effect of vectoring jet on the transverse aerodynamic characteristics of a slender body.
介绍了光学压敏涂料测压技术原理，光学压敏涂料的研制和其在风洞试验中的应用。
The principle and preparation of optical pressure sensitive paint and its application in wind tunnel test are introduced.
透气性测定通过恒压气源吹气测压法实现，透气性探头的核心部件是微压差传感器。
Permeability is measured by constant pressure air source blowing, core of the detector is micro differential pressure sensor.
该测压技术廉价、通用，在空气动力实验及民用工业领域有广泛的开发和应用前景。
This technique is cheap and universal, and there is a broad developing and applying prospect in aerodynamic test and civil-using industry area.
建立了一个测压试验洞壁干扰的改进修正方法，使测压与测力试验的修正方法一致。
For the pressure tests, an improved correction method is established in this paper, resulting in the coordinated correction approach for both pressure and force tests.
应用主动性前鼻测压法比较了运动和鼻粘膜减充血剂对鼻气道阻力（NAR）的影响。
The effect of both physical exercise and nasal decongestant on NAR was compared using active anterior rhinomanometry.
断开图3中的C、D处，利用、回油路测压法(或测泄漏量法)找到了有故障的转向缸。
Disconnect Figure 3 c, d, the use of manometry to circuit (or leakage measurement method) to find the fault has shifted the cylinder.
介绍了液压型光电式测压计的设计原则、结构特征、测试原理、试验方法及其技术性能。
The design principle, structure characters, testing principle and method, and technique capability of hydraulic photoelectrical pressure gauge are presented.
本文为NACA0012翼型在NH - 1风洞进行跨音速二维测压实验的研究报告。
This paper is a report of experimental pressure. Measurement research for NACA0012 airfoil in NH-1 transonic wind tunnel.
医用压力传感器是选用医用级聚氯乙烯、聚碳酸脂作为传感器的测压连接管和主体的材料。
Medical selection of medical grade pressure sensor is PVC, polycarbonate sensor manometry as a connecting pipe and the main material.
本文首先进行了测压模型的设计，研究了测压模型尺寸的设计、材料的选取以及测点布置。
First, this paper researches the wind pressure model such as: model dimension, model material and setting survey points.
结果表明：压力恢复稳态测压法求解启动压力梯度理论正确，方法简单，具有明显的优点。
The results indicate that using pressure build-up steady state pressure survey approach to calculate starting pressure gradient has obvious advantages with simple method and is theoretically correct.
由于这些特点，毛细管测压系统在使用时无深度限制，可以不受时间限制连续地测取井下压力。
Because of these characteristics, the pressure measurement system with capillary tubing can be used without depth limit and can measure the downhole pressure continuously without time limit.
将测压原理拓展应用到均匀送、排风管路的设计中，并探析了这种管路的作用机理及计算方法。
Applies the pressure measuring principle to the ducts for even air supply and exhaust, and analyses the function mechanism of such ducts and their application calculation.
有的异常高压油、气井由于受设备、技术条件限制而不能关井测压，无法获得不稳定测试资料。
Shut in pressures of some oil-gas wells with abnormal high pressure can not be tested as the limitation of equipment and technique conditions to fail in getting test data.
位移测试装置利用高精度差动变压器位移传感器完成塑性测压器件的变形量（或压后高）的测量；
The deformation or the highness after shooting of the plastic pressure-measuring elements is measured by the high precision LVDT displacement sensors in length testing device.
本文对动失速型非定常分离涡结构的控制方法，在低速风洞中应用相平均测压技术进行了实验研究。
Experimental investigation on the control of dynamic stall type vortex flow was made in a low speed wind tunnel by using phase averaged pressure measurement technique.
本文对动失速型非定常分离涡结构的控制方法，在低速风洞中应用相平均测压技术进行了实验研究。
Experimental investigation on the control of dynamic stall type vortex flow was made in a low speed wind tunnel by using phase averaged pressure measurement technique.
应用推荐