实际流片结果表明该模型切实可行。
这就是导致重新流片的原因。
文中还对的流片振幅大小的影响进行了讨论。
The effects of the oscillation amplitude of the spoiler over the vortex is also discussed.
当一个扰流片扬起的时候，另一边的机翼就会下降。
着重探讨了来流攻角和扰流片高度对过冲量的影响。
As a primary purpose, the effect of Angle of attack and height of spoiler on the unsteady flows are investigated.
同时，完成版图设计工作后在某工艺线上进行了流片。
In addition, the tape-out is carried out after the validation of the layout design.
南方群岛(si)的流片最近，台积电，现在通过移动。
Southern Islands (SI) taped out recently, and is now moving through TSMC.
理论模型和样品的设计需作下一步的流片进行实验验证。
With following experiments, the theoretical model and the designing structure will be verified.
所述内管是光管、螺纹管、内肋管或带有扰流片的管子。
The inner tube is a light tube, a screw tube, an inner rib tube or a tube with a spoiler.
本文介绍用涡面元法模拟带扰流片的翼型低速无粘分离绕流。
A vortex panel method is presented to simulate low speed inviscid separated flow past an airfoil with a spoiler.
通过流片，制作出肖特基栅共振隧穿三极管(SGRTT)。
Schottky gate resonant tunneling transistor (SGRTT) is fabricated.
最终进行了第二次实验批流片，测试结果满足最初的设计指标。
At last, we run the second experimental lots, and the test results met he original design specifications.
当两边的扰流片都扬起时，升力就会下降，阻力增加，飞机下降。
When both are raised, overall lift fall and drag increases, so the aircraft descends.
副翼比旧式喷气机上的要小，装载机翼顶部的扰流片可以辅助副翼。
Ailerons are smaller than on the older jets, and they are aided by spoilers mounted on the tops of the wing.
测试了工艺流片实验后MOS器件的性能，并对测试结果进行分析。
Testing MOS transistors including high voltage LDMOS and low voltage MOS after the process experiment, then analyze the results of test.
拢流片振动频率，对分离涡的尺度、强弱、成对、合并过程有重要影响。
The test results show that the scale, intensity, pairing and merging of the vortices depend, to a large extent, on the forced oscillation frequencies of the spoiler.
对双极晶体管结构和关键性能参数进行了研究和设计，并进行了流片测试。
The main structure and key performance parameters of the bipolar transistor were studied and designed, it was taped out and tested.
最后对子模块和整体电路的版图进行设计，流片后过对子模块和芯片整体测试。
And then designed the module and the whole circuit layout. After all measured modules and chips.
主要负责所有模拟电路版图的整体布局、静电保护设计和模块到顶层的集成设计和流片。
You will be responsible for all levels of analog mask layout from floor planning, ESD pad placement, block level layout up to top level integration tape out.
从非定常流场计算出发系统的研究了嗡鸣发生的机理以及扰流片对嗡鸣起抑制作用的机理；
Through solving the unsteady flow fields of an airfoil-flap, the mechanism of buzz is intensively studied.
设计完成后，流片测试结果表明，图像传感器可以采集清晰图像，性能良好，满足设计要求。
The testing results of a tape-out showed that the performance of the designed chip for CMOS Image Sensor is good, it is able to sample clear photos and meets the design requirements.
在风洞用电子扫描阀进行测压 ，研究了绕平板扰流片和锯齿扰流片分离流动的壁面压力分布 。
Wall pressure distribution induced by the saw-tooth flap has been investigated with electronic pressure scanner in wind tunnel.
标准方案历经了方案论证、系统仿真、样机研究、IC流片和产品机顶盒样机开发等多个研发阶段。
DMB-T has passed the phase of Project Demonstration, system simulation, Re search of Functional system, IC chips and STB product. After several kinds of lab.
并且一次流片成功，各项指标、参数都达到了设计要求，是一块具有自主知识产权的电源管理芯片。
It was successfully taped-out at the first time with each indicator and parameter meets the design goal, so it's a successful power management IC with own intellectual property.
干燥室上部加装陶析环及旋流片可以控制出口物料的粒度及湿度，以达到不同物料的终水份粒度的要求。
There are rotation flow pieces and elutriation ring inside the drying charnber . it is used to control the moisture and granule of raw material to the needed level.
经流片验证与严格测试，表明该模块线性好，性能优良，除用于高精度测温外，亦可作为单独产品获得应用。
Besides being as a precise temperature measurement module, it can be used as a sensor product and applied to industrial fields.
一种复式洗涤水膜除尘器，由进烟管、文丘里管、异形管（板）束，脱水旋流片、供水系统、排灰机和水池组成。
The water film duster for coal-burning boiler is composed of fume inlet, venturi tube, shaped tubular (plate) nest, dewatering swirl blade, water supply system, ash discharger and water pool.
文章分析和设计了一种具有较高电流控制精度和匹配精度的并联白光led驱动芯片，并在成功流片后进行了测试。
A high precise parallel white LED driver with finer current control precision and matching precision is analyzed and designed in the thesis. And the chip was tested after taped out successfully.
同时还给出了采用现场可编程门阵列(FPGA)芯片对设计电路进行功能验证的结果和ASIC流片的基本数据。
The circuit functions are verified with altera FPGA chips and the results of the verification and its ASIC synthesis with Synopsys DC are given.
同时还给出了采用现场可编程门阵列(FPGA)芯片对设计电路进行功能验证的结果和ASIC流片的基本数据。
The circuit functions are verified with altera FPGA chips and the results of the verification and its ASIC synthesis with Synopsys DC are given.
应用推荐