因为在这之后会用机器造出纸张，我们可以把这个步骤放在流程图的中间。
Because after that they use a machine to make the paper and we can put that right in the centre of the flow-chart.
现在，按照以下步骤来制作极好的思维导图。
在此流程的将来版本中(图25)，这些步骤现在是并行执行的。
In the To-Be version of the process (Figure 25), the steps are now done in parallel.
最终步骤(图17)允许您根据早期选项选择以(更新文件大小)保存可能与OV f信封相关的任何变更。
The final step (Figure 17) allows you to save any changes that might be relevant to the OVF envelope based on earlier option selections (update file sizes).
图13显示了需要的导航步骤。
图3显示了这些部署步骤的概述。
图2总结了上面所述的步骤。
图18显示这些步骤。
事件流关系图由交互集和业务步骤组成。
An event flow diagram consists of interaction sets and business steps.
图6展示了这些步骤。
图2总结了这些步骤。
后面几节详细解释每个步骤并提供屏幕图。
The following sections then provide detailed explanations and screen captures for the steps.
查阅“如何勾画火苗”有配着图的清楚的步骤指示。
See How to draw flames for some clear Pointers with step-by-step images.
图1显示了这些步骤。
图8显示了这些步骤。
图10显示了完成所有向导步骤后的组装图。
Figure 10 shows the assembly diagram after the wizard steps are complete.
图3中的步骤5到10说明这个过程。
处理步骤与图1相同，只是不需要把文档发送给客户机并发送回来。
The processing steps are the same as shown in Figure 1 except that the document is not shipped to the client and back.
作为上述步骤的结果，将生成图13 - 10中展示的构件。
As a result of these steps, the artifacts shown in Figure 13-10 will be generated.
注意图3的步骤8中FAILURE信号被发送回控制器中。
Notice in step 8 of Figure 3 that a FAILURE signal is sent back to the controller.
让我们一步一步地完成客户机发送请求时发生的消息流；步骤编号与图1相对应。
Let us step through the message flow that occurs when the client sends a request; the step Numbers correspond to those in Figure 1.
现在，Barb需要向IGAA指出，IGAA通过什么分析结果能够正确地引导她进入下一个分析步骤(图15)。
Now, Barb needs to indicate to IGAA what the results of the analysis were such that IGAA can properly guide her to the next step (Figure 15).
创建Web服务的步骤(编号与图2中的一样)如下。
The steps to create the web service, as numbered in Figure 2, are.
为企业服务提供门面接口的步骤（编号与图1中的一样）如下
The steps to provide a Facade interface for enterprise services, as numbered in Figure 1, are
复制过程由以下4 个主要步骤组成，如 图3 所示
The replication process consists of the following four major steps, as depicted in Figure 3
在步骤 2.1 的面板（图20）上，选择以下值
On the Step 2.1 panel (Figure 20), select the following values
您可以通过创建项目补丁和在ApplyPatch向导的TargetResource步骤(图4)中选择src文件夹来模拟这个行为。
You can simulate this behavior by creating the patch for the project and selecting the SRC folder in the Target Resource step (Figure 4) of the Apply patch wizard.
图10：rup步骤-改善测试资产。
图9中的步骤描述如下。
当接收到消息时，RMDestination中执行的步骤如 图7所示。
The steps that are executed in the RM Destination when a message is received are shown in Figure 7 below.
应用推荐