设计并构建了分布式步进电机控制系统。
We designed and constructed the distributing step motor controlling system.
用步进电机控制选择8种波长的滤光片;
主要包括信号采集电路和步进电机控制电路。
It mainly includes signal collection circuit and stepped motor control circuit.
实践表明,系统性能优于传统的步进电机控制器。
The practice shows that the performance of this system outdoes the traditional stepping motor controller.
通过对步进电机控制器编程实现了相位调制的自动化。
We can realize the automation of the phase modulation by programming the controller of stepper motor.
该包装机用于包装袋装的粉状类,计量系统为步进电机控制。
The packaging machine for packaging bags of powder type, the metering system for the stepper motor control.
步进电机控制实验是微机原理与接口技术课程中一个非常重要的实验。
Stepping Motor control experiment is a very important experiment in microcomputer principle and interface technology course.
TMS320C6713的步进电机控制实验程序,开发环境CCS。
TMS320C6713 stepper motor control experimental procedure, the development environment CCS.
硬件由微机、步进电机控制卡、步进电机驱动器和步进电机等器件组成。
Hardware consists of microcomputer, stepping motor control card, stepping motor driver and stepping motor and so on.
本文介绍了由计算机对步进电机控制从而实现多自由度运动的系统的设计。
A design of many-degree-of-Freedom stepping motor motion system, controlled by computer is introduced in this paper.
本机采用全自动伺服电机或步进电机控制长度,操作简便,封齿清晰美观。
This machine adopts full automatic servo motor or step motor for dead length, easy to operate, and the sealing is clear and beautiful.
针对这一问题设计一种差分信号转换器,有效地实现了步进电机控制功能。
For resolving this problem we design a kind of difference signal convertor. Through using the difference signal convertor the step motor is effectively controlled.
一种步进电机控制装置,通过廉价配置可以电检测步进电机负载并有效防止失步。
A control device for step motor, through low cost configuration can make the electric testing for the load of step motor and prevent braking step effectively.
在分析步进电机控制原理的基础上,提出了一种新的卷积算法,并推导了卷积系数。
Based on analyzing the control principle in stepping motor, a kind of new convolution algorithm is proposed and corresponding convolution coefficient is also deduced.
说明:步进电机微调程序,用于步进电机控制与检测。测试步进角度和自动计算机角度。
Stepper motor tuning program for stepper motor control and testing. Step angle and automatic computer testing point of view.
在对步进电机细分驱动原理进行深入研究的基础上。提出了一种新的步进电机控制方法。
A new step motor divided control circuit was given on the bases of studying principle of step motor divided driving.
着重讨论了单片机系统、样品箱恒温电路、样品位置检测电路和步进电机控制电路的设计。
The design of the single chip system, sample box thermostat circuit, sample position detecting circuit and step motor control circuit are discussed.
传统的膏药切片工艺是采用刀片对由步进电机控制的条状、长幅面的膏药进行机械式切割。
The traditional mechanical method is to use a knife to cut the plaster which is being controlled by a step-motor.
步进电机控制系统的开发采用了软硬件协同仿真的方法,可以有效地减少系统开发的周期和成本。
Stepper motor control system has been developed using the software and hardware co-simulation method, can effectively reduce the system development cycle and cost.
步进电机控制打料螺杆充填精度准确,该机用于包装袋装的粉状类,计量系统为步进电机控制。
Step motor controls filling-screw to reach high precision. The whole measure system is controlled by step motor too.
采用先进的微电脑控制器,驱动步进电机控制袋长及商标定位,性能稳定、调整方便、检测准确。
Adopt advanced microcomputer controller and step-by-step motor to drive and control the length of bag with stable performance and accurate testing. Meanwhile, it is easy to operate.
机械结构是一个安装在精密螺纹导引装置上的测试平台,通过步进电机控制反射镜组位移实现CCD采集。
Mechanical structure is installed in a precision-guided screw device test platform, stepping motor control through the mirror group displacement to achieve CCD acquisition.
阐述了步进电机控制原理,利用运动控制器实现了进给系统的联动控制,利用PLC实现了步进电机的点动控制。
The control principle of step motor is exposed, drive control of feed system is carried out by use of motion controller, meanwhile, dot motion control of step motor is also carried out by use of PLC.
设计了单片机端的控制程序,包括步进电机控制、编码器数据采集、RS232通讯、键盘读入、液晶显示屏输出等部分。
The controlling program in MCU part is designed, and it includes the part of step-motor controlling, data collection of the coders, RS232 communication, keyboard input, and LCD output.
介绍了一种基于PC机的IS A总线步进电机控制卡,实现多轴联动控制,讨论了其工作原理和硬件结构设计、软件设计。
One kind of stepping motor control card based on ISA bus of PC which achieved multi-spindle linkage control is introduced, its principle and design of hardware construction and software are discussed.
本文应用单片机、步进电机驱动芯片、字符型LCD和键盘阵列,构建了集步进电机控制器和驱动器为一体的步进电机控制系统。
In this paper, microcontroller, stepper motor driver chips, character LCD and keypad array, build a set of stepper motor controller and driver as one of the stepping motor control system.
DANCAD和DANCAM属于共享软件编写的程序由丹哈金斯提供2/3dimension起草和数控分别步进电机控制。
DANCAD and DANCAM are shareware programs written by Dan Hudgins which provide 2/3dimension drafting and CNC stepper motor control respectively.
该文介绍了一种简单的步进电机控制芯片LMD18245,利用它可以自行设计步进电机的驱动模块,从而为系统设计降低成本。
This paper introduces a simple stepper motor control chip LMD18245. By using it, we can design the drive module of stepper motor by ourselves, and thereby decrease the cost of system design.
当启动频率较高时,启动时会造成失步,而停止时由于惯性作用又会发生过冲,所以在步进电机控制中必须要采取升降速控制措施。
When the startup speed is higher, stepping motor will lose steps. While stopping, it will also lose steps because of inertia. So, it needs to take speed control measures on control of stepping motor.
详细说明:非常详细步进电机控制原理图,和完整的控制程序,安装PROTEUS后就可以看到仿真的结果,可是我呕心沥血做的,不容易!
Very detailed stepper motor control schematics, and complete control procedures, installation can be seen after the PROTEUS simulation results, but my heart out to do, not easy!
应用推荐