• 本文以300MW转子槽部温度最高的一段温度分布为例进行计算。

    The highest temperature distribution in the rotor slot section of 300mw turbogenerator is taken as example to be calculated in this article.

    youdao

  • 针对使用波纹板的大型发电机定子槽部固定结构,在实验室建立了槽楔松动模型。

    An experimental model is established in the laboratory to simulate the fixture structure of stator bars of large generators.

    youdao

  • 所述压粉铁芯部的至少一部分构成线圈槽部的至少一部分,在所述线圈槽部上缠绕有线圈。

    At least a part of the pressed powder core part forms at least a part of a winding slot part around which a winding is wrapped.

    youdao

  • 采用有限单元法,编制了适用于微机系统的槽部电场计算专用软件,计算了大型发电机定子线圈槽部电场的分布。

    The special microcomputer software for calculation of slot electric field is worked out with fe method, and the field distribution in stator slot winding of large generator is calculated.

    youdao

  • 保险库槽(vault slot)是保险库段的一部分;它是用CredentialSlotConfig类表示的。

    A vault slot is part of a vault segment; it is represented using CredentialSlotConfig class.

    youdao

  • 柔度算定试样是用一个有限端部半径的槽来代替裂纹。

    The compliance-calibration specimen has a slot of finite-tip radius in place of a crack.

    youdao

  • 木及木基板制内门。第2部分:门槽。术语尺寸和要求。

    Interior doors made from wood and wood - based panels - part 2: door crozes; concepts, sizes, installation.

    youdao

  • 结果:发现杵臼附着式固位的种植赝复体在行使功能时其腭部、牙槽骨、种植体周围骨界面的应力值均远高于杆卡附着式固位的种植赝复体。

    Results: the stress values of the ball attachment in the palate area, alveolar bone and implant bone interface were much higher than that of the bar attachment.

    youdao

  • 第四部分对球透镜的制备工艺进行研究,包括槽沉法制备球透镜、球透镜的抛光和基本性能测试。

    In the fourth part, the researches of preparation technology are proceeded, including fabricating ball lenses using sagging method, polishing of ball lenses and basic performance measurement.

    youdao

  • 如图中箭头所示:槽形托辊组成中对皮带运行有实质影响的唯一部分就是中心托辊。

    The only part of the troughing idler that hs any training effect on the conveyor belt is the center roll indicated by the arrow.

    youdao

  • 在单级轴流压气机上,用周向槽式处理机匣在静子内径处进行轮毂处理,与转子尖部机匣处理作类比。

    The hub treatment with a circumferential groove was tested on the stator hub and compared with the casing treatment over the rotor tip for a single stage axial flow compressor.

    youdao

  • 作为可选方案,所述齿能够从所述栓延伸,而且所述槽能够形成在所述第一部件的壁内。

    As an alternative, the teeth can extend from the peg, and the groove can be formed in the wall of the first component.

    youdao

  • 它由公扣和母扣组成,公扣的外周设有安装环槽,公扣的一端设有凸出部;

    The periphery of the male buckle is provided with an installing ring groove, and one end of the male buckle is provided with the bulge.

    youdao

  • 在第四部分的基础上,第五章再次对该天线设计做性能改善,使用二元折叠槽阵列天线。

    On the basis of Chapter Four, Chapter Five improves the performance of this antenna design by applying double folded slot antennas.

    youdao

  • 多个吸入通道允许有效的拾取脏物,其可通过为狭槽(48)形式的空气管道得到进一步地增强,该狭槽在工作边缘(42,44)的一部分之上吸入空气。

    The plurality of suction channels permits effective pick-up of dirt, which may be further enhanced by an air duct in the form of a slot (48), which draws air over some of the working edges (42, 44).

    youdao

  • 结论:以牙槽孔至颧下嵴起始部的弧长和弦长为标准弯制注射针头,采用口内注射法进行上牙槽后神经阻滞麻醉,成功率为98%。

    Conclusion: We use L as arch length and H as chord length to bend syringe needle that is used to posterior superior alveolar nerve block anesthesia by intraoral injection. The success rate is 98%.

    youdao

  • 发热部是双螺旋切槽,在电流通过时可以减少其横截面积,因而发热部的阻值比冷端部的阻值大。

    The hot zone is formed by cutting a double spiral slot which reduces the cross sectional area through which current flows, resulting in higher resistance than the cold end.

    youdao

  • 器具部(108)由2根叉子(110)构成,在2根叉子(110)中的1根的外侧形成有多个槽(112)而构成餐刀部(114)。

    The tool portion (108) is composed of two forks (110), one of which has a plurality of grooves (112) formed in its outer side thereby to constitute a knife portion (114).

    youdao

  • 另在定寸凸部上每隔适当距离处形成有延伸至衔接部的缺口槽。

    Notch grooves which are extended to the join part are formed on the dimension raised part in the interval of a proper distance.

    youdao

  • 另在定寸凸部上每隔适当距离处形成有延伸至衔接部的缺口槽。

    Notch grooves which are extended to the join part are formed on the dimension raised part in the interval of a proper distance.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定