研究了槽液成分，工艺条件及膜层性能。
Electrolyte components, operating conditions and film performance have been researched in this paper.
电泳槽要用环氧玻璃钢衬里以与槽液绝缘。
The electrocoat tank is lined with a fiber-glass-epoxy composite material to provide electrical insulation.
分析了影响电泳槽液稳定性的操作因素和管理方法。
The operating factors and control processes influencing the stability of the bath content are analyzed.
槽液运动方向指的是液面的运动方向相对于车身的运动方向。
The direction of paint flow refers to the direction of the movement of the top of the tank relative to the vehicle.
而改变槽液温度、活化条件可改变饱和色，但最深色调为桔红色。
When temperature of coloring solution and activation conditions change, it can be changed, but the deepest color tone is orange - red.
列出了槽液工作参数并指出了今后工艺管理中应注意的一些问题。
The technology paramtere of electrophoretic liquid and matters needing attention in process management are listed.
刚沉积电泳上的漆不溶于水，允许彻底清洗，且可回收带出的槽液。
Freshly-deposited paint is insoluble in water, permitting complete rinsing and recovery of dragged-out material.
槽液粘度低(大约等于水的粘度)，泵送容易，也利于被涂车身的沥干。
The low paint bath viscosity (approximately equal to that of water) results in ease of pumping and allows drainage of the coated vehicle.
浮选槽液位是浮选过程中一个很重要的工艺指标，液位控制有较高要求。
The pulp level of flotation cell is a very important technological index in flotation process, on whose control there are high requirements.
电镀槽液的管理和处理方法是决定电镀厂产品质量和经济效益的重要手段。
The maintenence and treatment of the plating bath plays a decisive part in ensuring product quality and economic benefits of the plating shop.
本文介绍采用TP—801单板机来实现扁位槽液位的直接数字控制系统。
This paper elaborates on a direct digital control system of level and the control system is going to be operated by the microcomputer TP-801.
经过热交换器冷却槽液，以除去由涂装电功及泵运行的机械功所产生的热量。
It provides paint cooling by circulation through the use of heat exchangers to remove heat generated by the electrical work of coating or that was created through the mechanical work of pumping.
这些交联剂于正常槽液温度下在水中很稳定，但在固化温度下就变得活泼起来。
These crosslinkers are stable in water at normal bath temperature but become reactive at curing temperatures.
磷化槽安装槽液连续添加和过滤清渣系统可保证磷化膜质量和拉丝的顺利进行；
Installing bath continuous adding and filter cleaning dregs system can ensure phosphate coating quality and …
利用X射线衍射技术，研究了由五种不同电镀槽液所获得的镀锌层中品体的取向。
Crystallographic orientation of electrodeposited zinc in five different electrolytes were studied by means of X-ray diffraction technique.
车身水平表面上方的槽液快速流动将最大限度地减少颜料和杂质在这些表面上沉淀。
The rapid flow of paint over the vehicle horizontals will minimize the settling of pigment and dirt on these surfaces.
30度的入槽角是既使工件迅速地侵入槽液中，又能保持槽的深度最小的择中方案。
The thirty-degree angle of entry is a compromise which permits the vehicle to be quickly submerged in the paint while keeping tank depth to a minimum.
通过对光亮镀镍工艺管理方法与槽液净化技术的浅显探讨，为同行提供一种工作方法。
The technological control method of Nickelex and technology of plating bath purification are briefly discussed, that can give a reference for other technologists in this industry.
叙述了参数测量项目及测量频率、槽液参数的影响与调整，以及漆膜常见缺陷的排除。
The items and frequency for parameter measuring, the effects of bath content and adjusting and trouble shooting for common defects of the paint film have been introduced.
直接加配槽液溶解，其他辅助材料特别是有机烷基，镍分子添加剂，也必须按比例补加。
Dubs in the tank liquor to dissolve directly, other accessory material are specially the organic alkyl, the nickel member chemical additive, must supplement in proportion.
加压过滤机是一种新型高效固液分离设备，其矿浆槽液位是影响该设备工况的关键参数。
Pressure Filter is a new type of high-efficiency solid-liquid separation equipment. The pulp liquid level is a key parameter of affecting the working conditions of the equipment.
阐述改进金属表面除油除锈工艺的必要性、工作机理、工艺全过程、槽液控制和主要特点。
This paper expounds the necessity for improving oil and rust removal process on metal surface, as well as its operating mechanism, the whole process, the bath control and its main characteristics.
用熔盐作为制备金属电沉积槽液的溶剂具有液态温度范围广和“电化学窗口”大等优异特点。
The fused salts as solvents for preparing electroplating bath have some important features, that is, their wider temperature range of liquid state and larger "electrochemical window".
该工艺在提高铝硬质阳极氧化槽液温度、增加膜的硬度和节能等方面都县有很大的实用价值。
This technology holds great practical values in raising the bath temperature for hard anodic oxidation of aluminium, improving the film hardness and energy saving etc.
该工艺在提高铝硬质阳极氧化槽液温度、增加膜的硬度和节能等方面都县有很大的实用价值。
This technology holds great practical values in raising the bath temperature for hard anodic oxidation of aluminium, improving t…
主要产品：清槽液、退膜液、消泡剂、绿油剥除剂、菲林清洁剂、洗网水、开油水、防白水；
The main productions:Cleanout Solvent, defoamer, Soldermask Stripper, Film-stripper, the special cleaner for PCB screen cleaning, the Anti-Static film cleaner, Copper cleaner and so on.
通过采用一些特殊的处理工艺，确保这些交联剂不会在槽液温度起反应而引起槽液的不稳定性。
Special procedures are used to ensure that these crosslinkers will not react at bath temperature to cause instability.
氨基树脂固化剂在阴极电泳涂料中存在槽液稳定性较差等问题，限制了其在电泳涂料中的应用。
Application of amino resin curing agents in cathodic electrophoretic coatings is limited for its poor stability in the bath.
研究了从焦磷酸盐槽液中电镀锡镍合金的一种新工艺，讨论了一些电镀参数对锡镍合金镀层的影响。
A new technology of tin-nickel alloy electroplating from a pyrophosphating bath was studied. The effect of some plating parameters on the tin-nickel alloy coating was discussed.
提出了一种适用于各种金属板贴塑的前处理工艺，着重介绍了脱脂和磷化的工艺配方、特点及槽液的维护。
Pretreatment process for PVC laminating on different thin metal sheets was introduced. Formula, strengths and maintenance of degreasing and phosphating process were emphasized.
应用推荐