用成熟的根切段进行同一个实验时，未观察到抑制作用。
When the identical experiment was performed with mature segments of roots, no inhibition was observed.
对渐开线齿形链轮的根切状态进行了研究，求解了不发生根切的最小齿数。
The undercut of the involute sprocket is investigated to derive the minimum tooth.
螺旋槽成形铣削时普遍存在根切现象，在很大程度上影响到加工精度和几何形状。
Usually, there exist undercutting phenomena in helical groove milling process, which affect the accuracy and geometrical shape greatly.
通过增加工作齿高和对根切条件的深入研究，提出了高齿准双曲面齿轮的优化设计方法。
An optimization design method for a hypoid gear with high tooth was proposed based on the investigations into variations of working tooth height and constraint conditions of undercut.
首次通过计算并控制摆线转子泵小转子廓线外凸部分最大曲率半径的方法来避免小转子廓线根切。
Simple explicit expressions for calculating the limit dimensions to avoid undercutting on the tooth profile of the small rotor in cycloid rotor pump are derived first time in this paper.
按常规方式加工小模数少齿数齿轮，容易出现齿轮根切现象，致使齿轮轮齿强度降低、齿轮啮合条件恶化。
To adopt usual way machining gear with small module and a few teeth, it is easy to emerge gear undercut, thus, it reduces the intensity of teeth and worsens the mesh condition.
通过VB编程，完成非圆齿轮节曲线设计、根切校验、封闭性条件、凸性校验等计算，并输出设计结果，实现非圆齿轮节曲线的计算机辅助设计。
Through VB programming, complete the calculation of noncircular pitch design etc and export the design results, then achieve Computer Aided Design of noncircular gear pitch.
该系统可完成SGM、SFM、SGT、SFT、HGM、HFM、HGT、HFT切齿法的齿坯几何参数、切齿调整参数、轮齿接触分析、磨齿调整参数和根切检验等计算。
The system can perform the computations such as blank dimensions, cutting and grinding settings, tooth contact analysis and under cut check of SGM, SFM, SGT, SFT, HGM, HFM, HGT, HFT cutting methods.
事故发生于凌晨1点30分的切迪·贾根国际机场。
The incident happened at about 1:30 a.m. at the Cheddi Jagan International Airport.
切斯·沃夫将那根烟丢到草里，碾碎了。
Czeslaw threw the cigarette on the grass and ground it to pieces.
首先需要获取图的根元素，这是一切工作的起点。
First of all, you need to obtain the root element of the graph. That's the starting point of everything.
直到有天，霍根意识到，全息原理改变了一切。
That is, not until Hogan realised that the holographic principle changes everything.
羊羔的骨头一根也不可折断。他们要照逾越节的一切律例而守。
They shall leave none of it unto the morning， nor break any bone of it： according to all the ordinances of the passover they shall keep it.
“对于切利亚我没有很多好话要说”，安德鲁·罗根，StreetDelivery的创始人兼首席执行官说道。
"I don't have much good to say about Ceglia," says Andrew Logan, founder and CEO of StreetDelivery.
所罗门为耶和华殿所造的两根铜柱，一个铜海，和几个盆座，这一切的铜，多得无法可称。
The bronze from the two pillars, the Sea and the movable stands, which Solomon had made for the temple of the Lord, was more than could be weighed.
他们打算让梅根吃饭，坐在餐桌上直到她开始吃，带她到医生那里去，甚至为她买营养饮料。但她拒绝了这一切。
They attempted to make Megan eat, sat with her until she ate, took her to the GP and even bought nutritional shakes, but she refused to touch them.
每一片树叶，每一根树枝，每一块石头，每一张蛛网在午后闪着光芒，犹如春天清晨的露珠浸润着这一切。船桨或昆虫的每一个动静都能让湖水闪出一道光辉。
Every leaf and twig and stone and cobweb sparkles now at mid afternoon as when covered with dew in a spring morning. Every motion of an oar or an insect produces a flash of light.
杜松根系观察及切根试验的研究。
Observation on Roots and Experiment on Root Cutting for Juniper.
由于案件疑点重重，巴西法官下令扣押罗切特和詹姆斯·费根的护照。
Brazilian judge orders the seizure of Lochte's and James Feigen's passports as doubts in the story develop.
分析了叶根数控加工中出现欠切的原因，提出了解决办法。
This paper has introduced the reason of undercut in blade root NC machining and pointed out the solving measures.
结论采用半切术技术保留下颌第一磨牙远中根的修复可获得满意效果。
Conclusion The hemisection can get satisfactory effect to repair the first mandibular molar with distal tooth reservated by selecting suitable tooth.
在配混过程中与基质聚合物混合之后，该非牢固的粘结发生破裂，并且该短切纤维束崩解成分散在基质聚合物中的单独的单根纤维。
Upon mixing in the compounding process with a matrix polymer, the fugitive bonds break, and the cut fiber bundles disintegrate into separate individual fibers dispersed in the matrix polymer.
所罗门为耶和华殿所造的两根铜柱、一个铜海和几个盆座，这一切的铜，多得无法可称。
The two pillars, one sea, and the bases which Solomon had made for the house of the LORD; the brass of all these vessels was without weight.
在三维雕刻加工中采用先进行层切粗加工然后进行清根精加工的解决方案。
A tool path scheduling methodology for 3D engrave models is presented, which performs rough machining by z-level milling first, then finish machining corner uncut material with pencil tracing.
根特先生对我坦承道：“能够当众发表演讲，享受这个过程带给我的乐趣，为社会提供额外的服务——这一切称得上我一生中最满意的事情。”
"The ability to make these talks, " he con-fessed, "the pleasure I get in giving them, the additional service I can render in the community-these are among the most gratifying things in my life.
把茎切整齐点，正好切在叶根下。
把茎切整齐点，正好切在叶根下。
应用推荐