介绍了PARR 6300 量热仪的工作原理、热容量标定、热值计算、使用注意事项及故障分析。
The working principle, thermal capacity calibration, calorific value calculation, attentions in operation and fault analysis of PARR 6300 calorimeter are introduced.
前两种地震仪，它们的运动方程和传递函数已知，传递函数系数可以通过经典的分段标定方法求得。
For the first two kinds the equations of motion and transfer functions are known. The coefficients of the transfer functions are determined by means of classical step-by-step calibration.
本文阐述了ndh—a型核子土基密度、含水量联合测定仪的测量原理、标定方法、使用试验及测试数据的分析。
This paper has described the measure principles, the calibration method, the application test and data analysis of the nuclear-earth-base-density-moisture-gauge of type NDH-A.
介绍了KZDL-3快速智能定硫仪的工作原理，并以实例说明它的标定方法及使用中应注意的事项。
The working principle of KZDL -3fast sulphur determination device is pre sented. Its calibration method and notable matters in application are described by using examples.
本文讨论了标定电流对标度值测量的影响，并介绍了研制的数字表标度值稳流仪及其使用效果。
Influence of calibrated current on scale value is discussed, and digital current stabilizer and its applied effect are introduced in this paper, respectively.
提出了一种基于浮动定标原理的示值标定方法。检测结果表明，它可以有效地扩大电阻式水分仪的示值标定范围，提高示值标定的精度。
A floating calibration method for resistance moisture teller is introduced. The results show the measuring ranges of the instrument are enlarged and the precision is improved by using this method.
本文采用快速失重式水分测量装置作为水分标定装置，对电导式水分仪进行在线标定。
This paper describes a rapid weight-loss method for the on-line calibration of conductivity moisture meter.
阶跃信号在地震仪的脉冲标定和检查中获得了广泛应用。
The step calibration signal has been widely used in seismograph calibration and check.
讨论了免标定和免维护在线监测仪的可行性。
The feasibility of the on-line monitor without calibration and maintenance is discussed.
研究了最小二乘拟合方法在CCD型光学多通道分析仪波长标定中的应用。
The application of the least square polynomial fit method in the wavelength calibration of the Optical multichannel analyzer with a CCD detector is investigated.
文中阐述了HGP - 1红外光谱仪工作原理、标定与测量方法，分析了误差来源及控制方法。
The paper expatiated the principles of HGP-1 infrared spectroradiometer. It introduced the methods of calibration and measure. The source and control measure of error were analyzed.
以三坐标测量机和激光跟踪仪为主要测量手段进行了标定试验。
Calibration experiments were made by CMM and laser tracker as main measuring methods.
报道了软x光能谱仪探测元件的能量响应曲线标定工作。
The calibration of the energy response of the detection elements for soft X ray spectrometer is reported.
因此，自标定过程中需要保证激光跟踪干涉仪的测距精度。
Hence, the accuracy of laser tracking interferometer should be high enough to ensure the accuracy of system self calibration.
现在对于距一标定过的地震仪任何距离处的任何一个地震，都可用一个震级确定之。
Any earthquake at any distance from a calibrated seismograph is nowadays assingned a magnitude.
在每次测量前需要手动标定X - Y记录仪的坐标以及切换测试项目间的油路，测试曲线绘制完成后也需要手动计算电液伺服阀的各项性能参数。
Before the test, the coordinates of the X-Y recorder are demarcated and the shifts of the test oil circuit are done manually. The parameters of the characteristics are also computed manually.
实践表明重块标定保证了倾斜仪较高的重复性和稳定性。
The result shows that heavy block calibration ensures the higher repeatability and stability of inclinometer.
文中介绍了光散射式数字粉尘测试仪各项指标的具体标定方法，并结合实际应用，总结了使用过程中应注意的事项。
This paper introduced the calibration of digital light scattering dust test instrument and mentioned some key points in measurement process.
介绍了ATOS流动式光学扫描仪的结构光三维扫描法工作原理和系统标定方法。
The working principle of 3d scanning with structured light and the system calibration of ATOS optical scanner are introduced.
传统的结构光三维测量系统对摄像机和投影仪的摆放有严格的要求或者标定过程较为复杂。
Traditionally the position between camera and projector is limited in the 3d measurement system based on structured light, or the process of system's calibration is very complicated.
零位校正误差是重力仪除标定以外最主要的误差来源。
Besides standardization, zero correction error constitutes the most common error source of a gravimeter.
介绍了使用冲击校准仪来标定虚拟仪器测量雷电冲击波形和操作冲击波形的试验过程和结果。
The experimental process and results of measuring impulse voltage and impulse current are introduced for using impulse calibration system to calibrate visual instrument.
论文介绍了测试仪的标定，主要包括机械定位、传感器检定。
The paper introduces demarcating of the instrument, such as mechanism orientation and sensor inspection.
简述型砂紧实率快速智能测试仪的技术原理，介绍了测试仪的设计、标定以及应用效果。
The technical principle of the intelligent high speed tester for solidity of moulding sand is described briefly. The design, calibration and application results of the tester are introduced.
介绍了一种基于微型光纤光谱仪的微型生化分析系统及其相应的标定和实验测试。
A micro biochemical analytical system based on a micro fiber spectrometer is introduced. Experiment was carried out to calibrate and test the analysis system.
一种度量仪器，例如探针、探头、触针或者触针支臂，用于安装在坐标定位仪上。
A metrology instrument, such as a probe, probe head, stylus or stylus arm, for mounting on a coordinate position apparatus.
针对一种立方构型的无陀螺仪惯性系统，分析了构型安装误差对惯性系统测量精度的影响及构型误差的标定方法。
The paper analyzed the effect of configuration fix-errors for a cube configuration gyro-free navigation system and presented a calibration scheme for fix-errors.
本文主要介绍利用岩心成像扫描仪对岩心进行扫描，来标定成像测井计算的裂缝、孔洞七参数的方法。
This article mostly introduces a method with which seven parameters of fractures and vugs can be calculated by imaging well logging through scanning rock core with imaging scanner.
通过GDOES 、XRD等手段标定表层成分和相结构，借助显微硬度计和球盘磨损仪测试合金渗层的性能。
The phase structure and composition of the modified layer was characterized by XRD and GDOES , and its properties were tested by microhardness meter and ball-plate wear instrument.
本文较详细地阐述了FD- 105 K测氡仪技术改造的思路并对测氡仪标定器的研制及应用作了介绍。
The thinking of the technical transformation on FD-105K Rn demarcation device and the development and application were introduced in detail in this paper.
应用推荐