板带轧制过程中因受某些因素影响会形成侧弯。
Synopsis There are some factors that cause the formation of hot strip side-camber in the rolling process.
冷轧板带的产品厚度精度是其一个重要的质量指标。
The accuracy in gauge of the cold rolling strip is one of the most important quality index.
板带轧制的三维变形理论是板形理论研究的重点和难点。
In shape theory, the three-dimensional deformation theory of plate and strip rolling is an important and difficult study content.
在板带递送机辊缝变形区中，板带表面容易发生塑性变形。
Plastic deformation is easy to occur on the surfaces of plate and strip in the roll gap of pinch mill.
该研究表明，弹塑性边界单元法用来分析板带轧制是满意的。
The research shows that the elastoplastic BEM is satisfactory for analyzing flat rolling of plate and strip.
变刚度系数是板带连轧机厚度自动控制系统中一个重要的参数。
Mill modulus control (MMC) is one of important methods in the automatic gauge control (AGC) systems of strip rolling mills.
介绍冷轧板带退火工艺的特点，探讨柳钢冷轧板带退火的设备选择。
The characteristics of cold-rolled strip annealing practice have been introduced, and the equipment selection of old-rolled strip annealing has been discussed.
提出模拟板带轧制过程三维变形的一种新的数值方法——流面条元法。
A new method-the stream surface strip element method (SSSEM) for simulating the three-dimensional deformations of plate and strip rolling process is put forward.
该研究结论对制定与完善板带轧制规程、提高板形质量具有重要意义。
The study results have significance for the setup and improvement of rolling regulations and plate shape quality.
本文在计算板带轧制中的参数时应用了初始应力的弹塑性边界单元方法。
In the paper, the elastoplastic boundary element method (BEM) of the initial strain is worked at calculating parameters of flat rolling of plate and strip.
冷却集管及喷嘴的结构和安装对于热轧板带层流冷却效果有重要的影响。
The structure and installation of the pipe nozzles have important effect on the cooling process of hot rolled strip and plate.
分析结果表明，轧制变形使板带晶粒细化，抗拉强度增加，伸长率降低；
The results show that the rolling will make the grain fine, the tensile strength increased and the prolongation rate reduced.
对板带材表面缺陷图像的识别与分类进行研究具有重要理论及经济价值。
The board strips surface defects inspection and classification can dedicate not only to the theory but also to the economical values.
轧制规程是板带生产的主要工艺技术内容，也是轧机机型选择计算的基础。
The pass schedule is the main technological substance in plate and strip production, and is the base of calculation of the rolling mills type selection.
研究了热轧板带厚度控制中轧制力预报环节的局部逼近神经网络实现方法。
This paper presents an artificial neural network model to predict the rolling force to control hot-rolled strip strip thickness.
板形平坦度自动控制系统是板带材冷连轧机过程控制系统的重要组成部分。
Flatness automatic control system is an important part of process control system of sheet or strip continuous cold rolling mill.
结果表明，半固态连续铸轧技术可以提高板带的塑性加工性能，细化晶粒。
The result shows that the technology of semi-solid strip casting and rolling can improve plastic processing property and refine grain.
板带轧机板形计算理论的研究是一个具有重要理论价值和实际意义的课题。
The study on strip shape computational theory of strip mill is a subject which has important theoretical value and practical significance.
通过改变轧辊、板带表面的应力分布，来得到理想的带材凸度、板形和厚差。
Optimum profile, shape and thickness difference of strip can be obtained by means of changing stress distribution of load on the surface of strip.
不均匀压缩下金属板带面内弯曲成形是一种不同于传统塑性弯曲的先进弯曲方法。
In-plane bending of a strip metal under unequal compressing with conical rollers is a kind of advanced bending processes.
详细讨论了基于有限元分析的钢筋混凝土和预应力混凝土楼板的板带截面设计方法。
The section design method of slab strips for reinforced concrete and post tensioned concrete slabs is discussed in detail.
在设计、改造板带轧机，以及控制和改善板形时都要对轧机辊系弹性变形进行考虑。
Roll elastic deformation must be considered when plate rolling mill is designed and rebuilt and plate shape is controlled and improved.
通过采用化学分析法和经验法加快了调试进度，提高了轧制稳定性和板带厚度精度。
By the method of chemical analysis and the experienced method, the commissioning with load was speeded up and the thickness precision of the strip and the rolling stability was improved.
这里详述了镁合金板带的双辊铸轧技术进展情况，概述了镁合金板带的其他生产工艺。
The new progress in magnesium strip roll casting is dwelled on, other magnesium plate and strip producing technologies are summarized in this part.
在整个变形区内板带边缘和中心的纵向相对应变较小，可以防止边缘出现起皱、鼓包。
The relative longitudinal strain between the strip edge and strip center is very small in the whole deformed zone, which can prevent appearing crinkling and bloating.
板形识别与板形控制技术的智能化实现是现代板带轧机控制中的世界前沿性研究课题。
As far as the technique is concerned, the key scientific problem in the world is pattern recognition and the realization of shape intelligent control.
本文提出了一种转动结构用于铜合金冷轧板带残余应力检测以及面内形变的测量方法。
In present paper a new rotating-structure was introduced to detect local residual stress and in-plane deflection in thin cold-rolled sheet of copper alloy.
介绍热轧板带生产线过程自动化、基础自动化、传动及检测仪表等系统的总体设计方案。
The general design of the process automation system, the basic automation system and drive system as well as the instrumentation system of Hot-rolled strip production line is introduced.
某些高级应用，如轿车用板带材生产线的压下控制等，对伺服性能提出了更加严格的要求。
Some advanced application, such as the product line of iron strip used for cars, requires more excellent response characteristic of hydraulic servo-system.
分析了柱上暗扁梁在楼盖中的作用，认为它不能起到框架梁的作用，应为柱上板带的一部分。
The analysis for the concealed wide-flat beams demonstrates that it belongs to the column strip and it does not possess the function of the frame girder.
应用推荐