• 螺杆泵井运行过程中经常出现杆柱断脱、蜡卡、烧泵等现象。

    For screw pump well, the following accidents, such as rod breaking, wax locking and pump burning, always happened.

    youdao

  • 在有杆抽油系统工作过程中,抽油杆柱的合理设计是非常重要的。

    Reasonable rod pump string design is very important in the working course of rod pump system.

    youdao

  • 许可证持有人须把所有杆柱髹上较淡的色彩。

    The Permit Holder shall paint all the pole structures in a colour of low chromatic intensity.

    youdao

  • 应用有限元法对辽河滩海油田大斜度定向井抽油杆柱受力进行了三维计算。

    Using finite element analysis method, three-dimensional calculation is conducted for force summing on rod in high-inclination well of Liaohe tidal zone oilfield.

    youdao

  • 从振动力学的理论出发,对现行抽油杆柱的振动力学模型进行了系统分析。

    Based on theory of vibration mechanics, this paper analyzes the vibration mechanics model of rod string systematically.

    youdao

  • 以抽油杆柱为研究对象,论述了斜直井游梁式抽油机冲程和冲次的计算方法。

    Taking the rod string as the object of study, a method of computing pumping stroke and speed of walking beam pumping units for slant straight wells is also presented.

    youdao

  • 根据斜直井抽油杆柱工况特点,建立了斜直井抽油杆柱的一维有阻尼波动方程。

    According to the operating mode of the rod string in slant straight Wells, the authors establish a one-dimensional damped wave equation for the rod string.

    youdao

  • 文章对抽油杆柱断脱的设计方法进行了详细的理论分析,指出了其中存在的问题。

    The paper gives a detailed analysis of the design method causing rod string dropout and points out its inadequacies.

    youdao

  • 应用第四强度理论,求解杆柱在扭矩和轴向力条件下的复合应力,设计抽油杆柱。

    Rod strings are designed by computing compound stress with the fourth strength energy on the condition of torque and axial force.

    youdao

  • 方法采用增大油管直径和下加重杆技术,来减少油流上升阻力和增大杆柱下行动力。

    Method Large diameter oil tube and weighting rod are adopted to decrease lifting resistance of crude oil and to increase lowering-in energy of the string.

    youdao

  • 采用力学分析的方法,结合测井资料,由下到上计算了抽油杆柱的扶正器间距和轴向力。

    The axial load and centralizer spacing from the bottom to the top are calculated by using the mechanical analysis method and the log data.

    youdao

  • 在对旋转抽油杆柱的扭转振动分析的基础上,给出了各阶扭转振动固有特性参数的计算式。

    On the basis of the analysis of the twisting vibration of rotary sucher-rod string, a formula of calculating every harmonic vibration eigenfrequency is presented.

    youdao

  • 针对水平井井眼具有一定曲率的特点,建立了抽油杆柱下部任意一点最小轴向力的计算方法。

    In the light of characteristics that horizontal hole possesses a certain rate of curvature, the method of estimating minimum axial force at any point along a rod string is established.

    youdao

  • 通过对螺杆泵采油系统进行分析,得到抽油杆柱力学模型,并对杆柱所承受载荷进行推导计算。

    Analysis screw pump system, get the mechanical model of rod string, deduct and calculate undertaking load of rod string.

    youdao

  • 在计算排出口压力计算过程中,考虑了由于抽油杆柱旋转引起杆管环空气液两相流摩阻的影响。

    To calculate discharge port pressure, this article considers the influence on frictional pressure drop in the gas and liquid two-phase flow between rod and tubing owing to rotation of rods.

    youdao

  • 采用力学分析的方法,结合井眼轨迹数据,由下到上逐跨计算了抽油杆柱的扶正器间距和轴向力。

    The axial load and centralizer spacing from the bottom to the top are calculated by using the mechanical analysis method and the well trajectory data.

    youdao

  • 结果表明,杆柱中的最大振动位移随深度增加量值逐渐增大,最大动应力随深度增加而逐渐减小。

    The results indicate that the maximum displacement increases, and the maximum dynamic stress decreases with depth.

    youdao

  • 针对井口驱动螺杆泵抽油杆柱断脱频繁的问题,应用弹塑性理论分析了抽油杆柱在井中的受力状况。

    In the light of the frequent breaking of the rod string in a surface driven screw pump well, the force condition of the string in the well is analyzed by means of the elastoplasticity theory.

    youdao

  • 由于定向井井身结构特殊,利用螺杆泵进行抽油时如不采取任何措施势必造成杆柱严重磨损甚至卡死。

    Due to the special structure of controlled direction well, it can lead to severe abrasion even jamming if not adopting any measure when using progressing cavity pump rod to pump oil.

    youdao

  • 根据求得的时域内抽油杆柱受力变形值以及与油管柱碰撞接触力,计算了抽油杆柱动强度和扶正器安放位置。

    The dynamic strength of rod string and the mount position of centralizer were calculated, according to the acquired deformation of rod string and its impact contact force with tube in the time domain.

    youdao

  • 螺杆泵工作时,杆柱不但受到拉应力,而且受到剪应力。如果设计不当或使用中监测不力,螺杆泵很容易发生故障。

    When screw pump works, the stem can not only influence by the force of tension stress but also the shearing stress which makes it to be failure easily if the design is not good or monitor is poor.

    youdao

  • 在某一给定条件下,对满足抽油杆柱强度要求的关系式进行了讨论,并绘制出了可校核抽油杆柱强度的线性关系图版。

    Under a given condition, strength expressions of rod string is discussed and a linear diagram is derived which can be used to check the strength of rod string.

    youdao

  • 通过此算法,能计算出抽油杆柱在任意时刻,任意截面的位移和载荷,而且该方法在计算时无条件稳定,特别适用于对斜井的预测。

    By using this method, it can evaluate the displacement and the load of any section at any time, and the method is stable, and it is especial adapt to the inclined well.

    youdao

  • 轴向力对具有初弯曲的杆(管)柱变形影响很大。

    Axial force has a great effect on deformation of rod or tubing with initial bending stress.

    youdao

  • 本文提出了一种用于筒体高层结构弹塑性地震反应分析的杆系——柱壳计算模型。

    A calculation model of bar system-cylindrical shell to be used for elastoplastic analysis of earthquake response of reinforced concrete tube structures is given in the thesis.

    youdao

  • 本文提出了一种用于筒体高层结构弹塑性地震反应分析的杆系——柱壳计算模型。

    A calculation model of bar system-cylindrical shell to be used for elastoplastic analysis of earthquake response of reinforced concrete tube structures is given in the thesis.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定