最后根据该机构的工作空间的特性,考虑了铰链摆动角的限制条件,给出了工作空间的解析式。
Taken into account of the constraint of joint angle, the closed-form workspace equation was given according to its characteristic.
经计算机模拟,得到了悬臂摆动角速度与悬臂摆角的关系曲线以及摆动力与悬臂摆角的关系曲线。
Relation curve between angular velocity and waving angular of boom and relation curve between swaying force and waving angular are obtained by computer simulation.
由于工作台摆动角度受机床结构的限制,小摆角五坐标数控机床不能直接进行离心叶轮的连续加工。
Five-axis NC machine tool with small pendulum Angle table can not carry out continuous cutting of the part of centrifugal turbine because of the structure of machine tool.
研究了基片摆动和基片自转的磁控溅射系统中基片摆动角振幅和基片自转角速度对磁控溅射膜厚均匀性的影响。
The influence of rotation speed and pendulum amplitude on the thickness uniformity of film deposited by radio frequency magnetron sputtering system with rotation and pendulum was researched.
经典的质心轨道根数,以及系绳在质心轨道面内与轨道面外的摆动角,均可由上述六个广义坐标及其广义速度确定。
All classic orbital elements and usual angular motion parameters can be calculated with the new set of generalized coordinates and their rates.
放低你的双臂,并用力摆动双臂,然后令你的双臂成90度角。
Drop your arms and shake them out. Then re-position them at a 90-degree Angle.
利用摆动活齿传动等效机构,分析其传动性能和最小传动角的位置。
According to its equivalent mechanism-crank rocker mechanism, driving performance and minimum driving Angle position of movable tooth is analyzed.
本文对摆动从动杆盘状凸轮机构的最大压力角和最小曲率半径问题进行了详细的讨论。
In this paper, the pressure Angle and minimal radius of curvature of CAM mechanism with swinging roller follower are discussed in details.
分析了摆动从动件盘形凸轮机构的压力角与基本尺寸之间的关系。
The relationship of cam with oscillating followers pressure angle and radius of basic circle were analyzed.
圆弧形自动门是往复摆动,其运动参数是每分钟摆动次数、摆角大小和行程速比系数等。
The circular arc automatic door is reciprocating swing, and its motion parameters are the number of swing per minute, the size of the swing Angle and the travel speed ratio coefficient.
在满足机构许用压力角条件下,采用0.618法最优确定盘状摆动凸轮机械的最小基圆半径。
Meeting requirement of the mechanical pressure angle, the minimum base radius of a plate cam for oscillating follower is determined by the 0.618 optimization method.
随着吃水深度的增加,平台的稳心高变大,但平台入水角减小,所以平台的容许摆动幅度降低。
As underwater depth increases, metacenter height increases, but water entry Angle decreases, so the platforms allowable swing angles also decrease.
目的分析多方位牵引床在牵引、屈曲成角、摆动和旋转时的力学原理。
Objective To analyze the principal mechanics of multi dimension instrument at the traction, flexion, oscillation, and rotation.
少年女子跳远二级运动员在着板瞬间和起跳过程中摆动腿膝角过大,折叠不紧。
Young female long jump two levels of athletes instantaneous and take off in the process in the board to swing the leg knee Angle oversized folds not tightly.
探讨了水翼瞬时攻角、及柔度对摆动水翼推进性能的影响。
The influence of the instantaneous angle of attack and ST on the performance of propulsion is investigated.
子弹的结构参数、转速对扫描角的摆动影响较大,通过调整子弹结构参数,可减小扫描角的摆幅。
The oscillation of scanning Angle is much influenced by the structure of bullet parameters and SOR. By adjusting the structure of bullet parameters, the oscillation amplitude can be decreased.
本文较为全面系统地推导了摆动滚子从动件圆柱凸轮的廓线、压力角及廓线曲率半径方程,并讨论了该种凸轮机构在各种运转情况下与之相适用的方程。
Mathematical formulas are derived comprehensively and systematically for the profile coordinate, pressure Angle and radius of curvature of the cylindrical CAM with an oscillating roller follower.
分析了摆动从动件盘形凸轮机构的压力角与基本尺寸之间的关系。
The relationship of CAM with oscillating follower's pressure Angle and Basic dimensions were analyzed.
对研究摆动从动件凸轮机构压力角和设计凸轮机构具有指导意义。
The results reported can provide a guidance in the research of the pressure angle of oscillating follower cam mechanisms and in the design of cam mechanisms.
“空气倍增器”和传统电风扇一样,能90度角摆动,同样功率确具有比传统风扇更大的风力。
Like the traditional electric fans can swing 90 degrees, the same power, even greater than in the traditional fan-type air.
在此基础上,设计了平衡滑翔情况下满足侧向摆动式机动及飞行约束所需的攻角变化规律。
Based on the flight corridor and equilibrium glide assumption, we can determine the angle-of-attack that satisfies the lateral weaving maneuver and all the flight constraints.
结论:程晓燕在起滑时左腿摆动垂直分速过大,水平分速相对较小,重心腾起角增大;
Conclusions: At the gliding stage, Cheng Xiao-yan the swing legs vertical speed too high, level speed too smell and the enlarging angel of body gravity ;
提出造成气膜端面密封角向摆动自振的内在机理,既有半频摆动自振又有角向气锤自振。
It is posed that angular air-hammer self-excited vibration and half frequency wobble self-excited vibration are two reasons for resulting angular wobble self-excited vibration for gas film face seals.
提出造成气膜端面密封角向摆动自振的内在机理,既有半频摆动自振又有角向气锤自振。
It is posed that angular air-hammer self-excited vibration and half frequency wobble self-excited vibration are two reasons for resulting angular wobble self-excited vibration for gas film face seals.
应用推荐