本文主要是用CAD对拉刀进行设计。
对圆孔拉刀的计算机程序设计及绘图进行研究。
In this paper the computerized programming and plotting of internat cylindrical broach are studied.
介绍了用于加工发动机连杆的组合拉刀cad系统。
CAD system for combined broach used to machine the automobile connecting rod is introduced.
文中简要介绍了涡轮盘枞树形榫齿精拉刀的设计方法。
This thesis briefly introduces the design methods of the fir-tree tenon tooth accurate broach of turbine disk.
介绍了加工曲轴用车拉刀的结构原理和设计、加工要点。
The structure principle, designing and manufacturing key points of the turning - broaching cutter for machining crankshafts are introduced.
针对被加工材质特点，设计合理的拉刀，并改进了冷却方式。
The proper broach was designed and the cooling method was improved in view of the feature of processed material.
本文介绍了一种加工管钳牙板上三角齿用拉刀的设计和计算方法。
In this paper, the design and calculating method of a kind of broaches for machining triangular tooth on the die has been introduced.
主要用于刃磨铣刀、铰刀、拉刀、盘形车刀、插齿刀及扩孔钻等。
Mainly Renmo milling cutter, reamer, pulling knives, plate-shaped lathe tool, knife inserted teeth and bore drilling.
本文介绍同心式内径定心矩形花键拉刀的设计特点和使用中的优点。
In this article, rectangular spline broach of the concentric form and internal diameter centering is introduced; and its design characteristics and advantages of the application are depicted.
介绍用拉削加工精密小深孔的工艺方法及拉刀的设计、参数的选择。
This paper introduces the technology of broaching accurate, small deep hole and the design of broaching tool as well as its parameter's selection.
根据国家标准关于对称度的检测规定，推导出了矩形花键拉刀对称度的检测方法。
On the basis of the national standard regarding testing symmetricity, the testing method for the symmetricity of rectangular spline broaches was put forward.
通常使用的是基孔 制，因为这会减少所需要的钻头、铰刀、拉刀和计量工具的种类。
Usually the hole-based system is used, as the results in a reduction in the variety of drill, reamer, broach and gauge tooling required.
文章讨论了缩短大直径拉刀长度的一般规律，以及根据各种拉刀的特点，缩短其长度的特殊措施。
General rule for shortening length of long broach with big diameter is discussed, and special measures for shortening various broaches' length based on their features are also introduced.
严重的碳化物带状偏析，使拉刀产生局部淬火过热和回火不足，造成内应力急剧增高，最终导致拉刀断裂。
It was found that the broach was locally overheated due to band segregation of carbide, and under-tempered. These factors caused fracture of broach as a result of high internal stress.
分析了现有渐开线花键拉刀的缺陷，提出带侧刃后角的渐开线花键拉刀的磨削工艺，并进行了齿形设计及齿形误差分析。
The current involute spline broach is analyzed, the grinding technology of involute spline broach with side clearance is described, the profile is designed, and profile error is analyzed.
论述了圆孔拉刀全参数化计算机辅助设计软件中有关拉刀各部分尺寸计算，总体程序设计，自动生成零件图及其强度校验的实现方法。
This paper deals with the realization of dimension calculations general programming, parts pattern auto -forming and strength test in the whole parameter CAD Software of the round hole broach.
祭司说：“ 你在以拉谷杀非利士人歌利亚的那刀在这里，裹在布中，放在以弗得后边，你要就可以拿去。
The priest replied, "The sword of Goliath the Philistine, whom you killed in the Valley of Elah, is here; it is wrapped in a cloth behind the ephod.
安吉拉：“你知道如果你需要我总是能帮你，不惜两肋插刀。”
Angela: "you know I'm always here to help you and would go out on a limb if you asked me to."
在切纸机工作过程中，纸辊的拉纸速度和刀辊的旋转速度共同决定了切下纸张的长度。
During the working of paper cutting machine, both the speed of drawing paper and the revolving speed of cutter decide the length of paper.
微小型高转速刀柄可实现金属切削机床的手动和（或）自动换刀；由锥柄和拉钉组成；
The microminiature high rotating speed tool shank can realize the manual or automatic tool changing of the metal-cutting machine, and is composed of a taper shank and a pull nail;
如错误操作有：运行状态拉合小车、热备用状态合地刀（挂地线）、检修状态合小车等。
Normal positions: running condition, hot standby mode, cold standby mode, maintenance condition, and trolley operation conditions, etc.
如错误操作有：运行状态拉合小车、热备用状态合地刀（挂地线）、检修状态合小车等。
Normal positions: running condition, hot standby mode, cold standby mode, maintenance condition, and trolley operation conditions, etc.
应用推荐